manualshive.com logo in svg

Allied Telesis AT-S63, Features Manual

The Allied Telesis AT-S63 is a high-performance network switch that offers advanced features and seamless connectivity. For easy setup and configuration, download the free Cli User's Manual from our website manualshive.com. This comprehensive manual guides you through every aspect of the product, ensuring optimal performance and reliability.

Share
Download
background image

Chapter 11: Classifiers

132

Section II: Advanced Operations

Observe these guidelines when using this criterion:

ˆ

The Protocol variable must be left blank or set to IP.

ˆ

You cannot specify both an IP ToS value and an IP DSCP value in the 
same classifier.

IP Protocol (Layer 3)

You can define a traffic flow by the following Layer 3 protocols:

ˆ

TCP

ˆ

UDP

ˆ

ICMP

ˆ

IGMP

ˆ

IP protocol number

If you choose to specify the protocol by its number, you can enter the 
value in decimal or hexadecimal format. It the latter, include the prefix “0x”. 
The range for the protocol number is 0 (0x0) to 255 (0xFF).

Source IP Addresses (Layer 3)
Source IP Mask (Layer 3)

You can define a traffic flow by the source IP address contained in IP 
packets. The address can be of a subnet or a specific end node.

You do not need to enter a source IP mask if you are filtering on the IP 
address of a specific end node. A mask is required, however, when you 
filter on a subnet. A binary “1” indicates the switch should filter on the 
corresponding bit of the IP address, while a “0” indicates that it should not. 
For example, the subnet address 149.11.11.0 would have the mask 
“255.255.255.0.”

Observe this guideline when using these criteria:

ˆ

The Protocol variable must be left blank or set to IP. 

Destination IP Addresses (Layer 3)
Destination IP Mask (Layer 3)

You can also define a traffic flow based on the destination IP address of a 
subnet or a specific end node.

You do not need to enter a destination IP mask for an IP address of a 
specific end node. A mask is required, however, when filtering on a 
subnet. A binary “1” indicates the switch should filter on the corresponding 
bit of the IP address while a “0” indicates that it should not. For example, 
the subnet address 149.11.11.0 would have the mask “255.255.255.0.”

Summary of Contents for AT-S63



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT-S63

IBM E02HRLL-G - WebSphere Partner Gateway... Administration Manual preview
E02HRLL-G - WebSphere Partner Gateway...
Brand: IBM Pages: 268
R&S FSV-K7 Operating Manual preview
FSV-K7
Brand: R&S Pages: 262
Olympus DS 20 - 128 MB Digital Voice Recorder Online Instructions Manual preview
DS 20 - 128 MB Digital Voice Recorder
Brand: Olympus Pages: 48
EVGA PC-over-IP Administrative Interface User Manual preview
PC-over-IP Administrative Interface
Brand: EVGA Pages: 108
Red Hat Cluster Suite Manual preview
Cluster Suite
Brand: Red Hat Pages: 188
GRASS VALLEY HDSTORM Datasheet preview
HDSTORM
Brand: GRASS VALLEY Pages: 4
GRASS VALLEY K2 FCP CONNECT - Installation Manual preview
K2 FCP CONNECT -
Brand: GRASS VALLEY Pages: 52
Sun Microsystems VIRTUALBOX 3.0.0 User Manual preview
VIRTUALBOX 3.0.0
Brand: Sun Microsystems Pages: 259
Yamaha CL3 Installation Manual preview
CL3
Brand: Yamaha Pages: 8
Autodesk 057B1-41A111-1001 - AutoCAD LT 2010 User Manual preview
057B1-41A111-1001 - AutoCAD LT 2010
Brand: Autodesk Pages: 574
DigiDesign Synchronic Manual preview
Synchronic
Brand: DigiDesign Pages: 68
Cabletron Systems SSR-ATM29-02 User Manual preview
SSR-ATM29-02
Brand: Cabletron Systems Pages: 386
KAPERSKY ANTI-VIRUS 5.7 - FOR LINUX FILE SERVER Administrator'S Manual preview
ANTI-VIRUS 5.7 - FOR LINUX FILE SERVER
Brand: KAPERSKY Pages: 104
Quantum PX500 Series Quick Start Manual preview
PX500 Series
Brand: Quantum Pages: 6
Samsung SC-X300L User Manual preview
SC-X300L
Brand: Samsung Pages: 116
Cabletron Systems CoreWatch User Manual preview
CoreWatch
Brand: Cabletron Systems Pages: 495
Brother VM-100 Brochure preview
VM-100
Brand: Brother Pages: 8
Brother BES Monogramming Suite Installation Manual preview
BES Monogramming Suite
Brand: Brother Pages: 10

Brands by name

Popular brands

Load more brands