manualshive.com logo in svg

Allied Telesis AT-S63, Features Manual

The Allied Telesis AT-S63 is a high-performance network switch that offers advanced features and seamless connectivity. For easy setup and configuration, download the free Cli User's Manual from our website manualshive.com. This comprehensive manual guides you through every aspect of the product, ensuring optimal performance and reliability.

Share
Download
background image

Chapter 24: Port-based and Tagged VLANs

280

Section VI: Virtual LANs

ˆ

Port VLAN Identifier

Note

For explanations of VLAN name and VLAN identifier, refer back to 
“VLAN Name” on page 273 and “VLAN Identifier” on page 273.

Tagged and

Untagged Ports

You need to specify which ports will be members of the VLAN. In the case 
of a tagged VLAN, it is usually a combination of both untagged ports and 
tagged ports. You specify which ports are tagged and which untagged 
when you create the VLAN.

An untagged port, whether a member of a port-based VLAN or a tagged 
VLAN, can be in only one VLAN at a time. However, a tagged port can be 
a member of more than one VLAN. A port can also be an untagged 
member of one VLAN and a tagged member of different VLANs 
simultaneously.

Port VLAN

Identifier

As explained earlier in the discussion on port-based VLANs, the PVID of a 
port determines the VLAN where the port is an untagged member.

Because a tagged port determines VLAN membership by examining the 
tagged header within the frames that it receives and not the PVID, you 
could conclude that there is no need for a PVID. However, the PVID is 
used if a tagged port receives an untagged frame—a frame without any 
tagged information. The port forwards the frame based on the port’s PVID. 
This is only in cases where an untagged frame arrives on a tagged port. 
Otherwise, the PVID on a tagged port is ignored.

Guidelines to

Creating a

Tagged VLAN

Below are the guidelines to creating a tagged VLAN.

ˆ

Each tagged VLAN must be assigned a unique VID. If a particular 
VLAN spans multiple switches, each part of the VLAN on the different 
switches must be assigned the same VID.

ˆ

A tagged port can be a member of multiple VLANs.

ˆ

An untagged port can be an untagged member of only one VLAN at a 
time.

ˆ

The switch can support up to a total of 4094 port-based, tagged, 
protected ports, and MAC address-based VLANs.

Summary of Contents for AT-S63



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT-S63

Califone AV Tutor MCFBV1-D Specification preview
AV Tutor MCFBV1-D
Brand: Califone Pages: 1
GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Installation & Programming Instructions preview
GARDTEC SPEECH DIALLER
Brand: GARDINER TECHNOLOGY Pages: 38
Blackberry TICKETMASTER - LEARN MORE User Manual preview
TICKETMASTER - LEARN MORE
Brand: Blackberry Pages: 7
Alcatel VitalQIP Specifications preview
VitalQIP
Brand: Alcatel Pages: 4
ASCOM DURAALARM - 1 Brochure preview
DURAALARM - 1
Brand: ASCOM Pages: 28
Toshiba HDWC110XK3J1 Quick Start preview
HDWC110XK3J1
Brand: Toshiba Pages: 1
Toshiba dynadock Drivers Update preview
dynadock Drivers
Brand: Toshiba Pages: 3
Toshiba e-STUDIO Printer/Fax/Scanner/Copier Brochure preview
e-STUDIO Printer/Fax/Scanner/Copier
Brand: Toshiba Pages: 4
Toshiba 6F3A4508 Instruction Manual preview
6F3A4508
Brand: Toshiba Pages: 53
Garmin GPSMAP GPSMAP 196 Specifications preview
GPSMAP GPSMAP 196
Brand: Garmin Pages: 2
Garmin MapSource User Manual preview
MapSource
Brand: Garmin Pages: 32
3Com H3C IMC STANDARD PLATFORM - Installation Manual preview
H3C IMC STANDARD PLATFORM -
Brand: 3Com Pages: 68
Altigen AltiSupervisor Manual preview
AltiSupervisor
Brand: Altigen Pages: 34
da Vinci Technologies EE Pro User Manual preview
EE Pro
Brand: da Vinci Technologies Pages: 249
Livescribe Desktop 2.3.1 User Manual preview
Desktop 2.3.1
Brand: Livescribe Pages: 88
Oracle Enterprise Manager Installation And Configuration Manual preview
Enterprise Manager
Brand: Oracle Pages: 38
PressReader Android Tablet Software User Manual preview
Android Tablet Software
Brand: PressReader Pages: 4
Saitek WII GAMESHARK CHEAT SAVES AND MEDIA MANAGER Manual preview
WII GAMESHARK CHEAT SAVES AND MEDIA MANAGER
Brand: Saitek Pages: 15

Brands by name

Popular brands

Load more brands