manualshive.com logo in svg

AJA FS3, Installation And Operation Manual, Page: 64 / 108

Share
Download
AJA FS3 Installation And Operation Manual Download Page 64

FS3 Frame Synchronizer/Converter v1.1r1 64 www.aja.com

 

When Adjust mode is selected:

•  After selecting an individual channel adjustment menu, the ADJUST knob 

changes the value shown by 0.5 dB (up or down) for each knob detent. 

•  The range of adjustment is -18.0dB to +18.0dB.
•  Switching from Unity to Adjust will apply the individual level values that were 

set in the Adjust mode to the input for each of the channels. Switching from 

Adjust to Unity will apply unity (0.0dB) to all channels.

1.1-1.16 SDI 1 Channel Levels

When Adjust is selected above, individual SDI 1 audio channel menus become 

available, perm/- 18.0 dB level adjustment to each input channel.

2.0 SDI1 Phase

This parameter selects the Audio Phase Mode for all 16 SDI1 audio input channels 

The default Unity setting applies normal (non-inverted) phase to all the input 

channels.

Unity (default)

Adjust

All 16 SDI1 audio input channels are set to Normal phase. Individual 

channel adjustment menus are hidden.

Each of the 16 SDI1 audio input Phase values (either Normal or Invert) 

are applied to the audio processor, and the individual channel 

adjustment menus become available. 

When Adjust mode is selected:

•  After selecting an individual channel adjustment menu, the ADJUST knob 

toggles the Phase value shown between Normal and Invert. When Invert is 

selected the phase of the audio input on that channel will be inverted.

Switching from Unity to Adjust will apply the individual Phase values that were 

set in the Adjust mode to the input for each of the channels. Switching from 

Adjust to Unity will apply unity (Normal) to all channels. 

2.1-2.16 SDI 1 Channel Phase

When Adjust is selected above, individual SDI 1 audio channel menus become 

available, permitting inverting the phase of each input channel. 

3.0 SDI1 Delay

This parameter selects the Audio Delay Mode for the eight SDI1 audio input 

channel pairs. Delay operates on channel pairs only. Delay cannot be adjusted 

on any single channel. Channel pairs are grouped as: Channel 1 and 2, Channel 

3 and 4,…, Channel 15 and 16. The default Global setting applies the currently 

set Global delay value to all eight input channel pairs. The factory default Global 

setting is 0 seconds delay, but whatever value the user changes this setting to will 

be applied when Global is selected. 

Global (default)

Channel Pair

All eight SDI1 audio input channel pairs are set to the current Global 

delay value. Individual channel adjustment menus are hidden.

Each of the eight SDI1 audio input channel pairs delay values are 

applied to the input of each channel pair, and the channel pair 

adjustment menus become available.

When Channel Pair mode is selected:

•  Each of the individual eight SDI1 audio input channel pair delay values are 

applied to the input delay of each channel pair. 

•  The range of delay is -16ms (-768 samples) to +256ms (+12288 samples). 48 

samples = 1 millisecond.

Summary of Contents for FS3













































































































Reviews:

No comments