AJA FS3 Installation And Operation Manual Download Page 54

Page: 54 / 108

FS3 Frame Synchronizer/Converter v1.1r1 54 www.aja.com

NOTE: If Custom Size/Pos is On and any of the following parameter are not set to unity,

the front panel UFC LED lights.

14.0 Custom Size/Pos

This parameter turns custom image settings On or Off.
When Hide Inactive is on, the Custom Size/Position controls are only displayed

when Custom Size/Pos is On. When Custom Size/Pos is Off, modified parameters

are skipped in the menu system, and the UFC hardware is programmed for unity.
This menu is also not displayed when Active Format Description (AFD) is in

control of the Conversion Mode.

Off (default)

Sets this parameter and related custom size/pos parameters to off.

Enables this parameter and related custom size/position parameters.

14.1 Custom Size

This parameter changes the H and V size of the output picture by the specified

percentage (%) while maintaining the current aspect ratio.

100% (default)

10% to 200%

Maintains 100% picture size for the selected format.

Enables changing the picture size.

14.2 Custom Aspect

This parameter changes the H/V aspect ratio of the output picture while

maintaining the current V size (Aspect < 0) or H size (Aspect > 0).

0.000 (default)

-0.500 to +0.500

Maintains the normal 100% aspect ratio for the selected format.

Enables changing the aspect ratio.

14.3 Custom H Position

This parameter changes the H position of the output picture.

0% (default)

-100% to +100%

Maintains the normal horizontal position of the selected format.

Enables changing the horizontal position.

14.4 Custom V Position

This parameter changes the V position of the output picture.

0% (default)

-100% to +100%

Maintains the normal 100% vertical position of the selected format.

Enables changing the vertical position.

14.5 Custom Left Crop

This parameter changes the Left picture crop position.

100% (default)

+10.0% to +100.0%

Maintains the normal left side position of the selected format.

Enables changing the left side position.

14.6 Custom Right Crop

This parameter changes the Right picture crop position.

100% (default)

+10.0% to +100.0%

Maintains the normal right side position of the selected format.

Enables changing the right side position.

Summary of Contents for FS3













































































































Search results

Summary of Contents for FS3

Reviews:

AJA FS3, Installation And Operation Manual, Page: 54 / 108

Search results

Summary of Contents for FS3

Reviews: