manualshive.com logo in svg

AJA FS3, Installation And Operation Manual, Page: 13 / 108

Share
Download
AJA FS3 Installation And Operation Manual Download Page 13

FS3 Frame Synchronizer/Converter v1.1r1 13 www.aja.com

 

Operational Summary

The seven front panel pushbuttons allow you to select display menu groups. 

The two knobs allow you to change menus and set parameters within the menu 

groups. These functions can be summarized as follows: 

•  Select a menu group: Press one of the seven pushbuttons. 
•  Scroll through menus in a group: Turn SELECT. 
•  Edit a menu parameter: Stop SELECT on the menu.
•  Change a parameter value: Once the parameter is selected with SELECT, turn 

ADJUST to set the value. Changes are applied immediately.

•  To edit a multiple part parameter, such as the IP address, push the ADJUST 

knob momentarily (the value blinks). To save the whole parameter after 

editing, push ADJUST momentarily again.

•  Coarse adjust a value (for use with parameters that have more than 10 

selections):
•  10x speed - Hold down the menu group button (the button turns blue) and 

turn ADJUST. The values will change in 10x increments. 

•  100x speed (available for extremely wide-range parameters, like Audio 

Delay) - After enabling 10x speed above, momentarily release and press that 

group button a second time (the button turns light blue). Turning ADJUST 

will now change the value in 100x increments.

•  Undo a change (restore previous setting): Push SELECT momentarily. 
•  Reset to factory default: Hold down ADJUST for 4 seconds. 

Button Operation Rules

The general rules of Menu Group button operation are:

•  Press one of the Menu Group buttons to access the associated menu group. 

The SELECT and ADJUST knobs control the display menus. 

•  The selected Menu Group button lights and the other buttons go low tally 
•  Each menu group returns to the last menu changed when you select the 

button. After a reboot, each group displays the last menu selected.

•  Hold down a button (turns blue) to make coarse adjustments using the 

ADJUST knob. Release the button to make fine adjustments (see above).

STATUS

Displays the Status Menu Group, which shows current machine status and error 

conditions:

•  Video Input and status
•  Caption status 
•  Reference and Genlock status
•  Output status
•  Power and Temperature status
•  System Name display
•  Alarms

REMOTE

Displays the Remote Menu Group, which lets you select how to control the FS3:

•  Control by local front panel only, remote sources only, or local and remote
•  Authentication
•  GPI input and output behavior

Summary of Contents for FS3













































































































Reviews:

No comments