manualshive.com logo in svg

AJA FS3, Installation And Operation Manual, Page: 43 / 108

Share
Download
AJA FS3 Installation And Operation Manual Download Page 43

FS3 Frame Synchronizer/Converter v1.1r1 43 www.aja.com

 

11 Fan Speed

This parameter determines the speed (and sound level) of the FS3’s internal 

cooling fans. To prevent system damage, this setting may be overridden 

temporarily, and the fan can be set to a higher speed if the system detects very 

high internal temperatures. Changes to this setting are automatically saved 

Variable

Changes the fan speed in steps from 1 (slow) to 10 (fast).  

Default is 10.

12 Serial Number

This parameter displays the FS3’s unique serial number. 

13 Software Version

This parameter displays the FS3’s software version number.

14 Reboot

This parameter lets you reboot the FS3. Press and hold in both front panel knobs 

simultaneously to reboot. 
During reboot, the display shows [Rebooting], goes dark momentarily, and then 

shows the percentage of progress as the system reboots. Rebooting takes a 

couple of minutes.

PRESET Menu Group

The PRESET Menu Group provides the means of saving, editing the names of, and 

loading FS3 presets. A preset is a set of all System, Video, Audio, and most Config 

parameters as they were set at the time the preset was stored. 

 

Caution! When you recall a Preset Configuration, the recalled preset immediately 

replaces the system’s existing configuration. All previous settings are lost unless 

you have previously stored them in another preset configuration or an exported 

file.

During recall, the display reads, Recalling until the recall is finished. On recall 

completion, the displays shows the success or failure: Recalled, Failed, or Empty. A 

failed or empty recall does not recall anything and leaves the FS3 as it was. (Preset 

registers are empty until you store something in them.) 
During a store, the display reads Storing until the store is finished. On store 

completion, the display shows Complete or Failed. A failed store does not store 

anything and leaves the preset register as it was. To retry a failed store, turn 

SELECT to another preset number and then back to the desired preset number. 

1 Factory Preset

This parameter recalls a read-only Factory Preset.

Factory

Recall 

Recalls factory values for all 

System

, 

Video

, 

Audio

, and most 

Config

 

parameters. Push 

ADJUST 

momentarily to perform (take) the recall. 

The display reports “Loading” and “Complete” during the recall. 

User preferences, network settings, and existing Presets are not 

affected by recalling the Factory Preset.

Summary of Contents for FS3













































































































Reviews:

No comments