AIC WAIKATO Expresso 72560 Installation Manual Download Page 53

Page: 53 / 71

Expresso Tie Stall

(AIC) 608.526.6882

#20560 Diaphragm Pulsator Solenoid Valves:

Specifications:

Input power

—

Nominal 24 VDC regulated power.

Current Draw—

20mA at 24 VDC

Solenoid Coil Resistance—

1.1K to 1.2Kohms

Servicing the Diaphragm Style Pulsator: (Solenoid Replacement)

The pulsator solenoid valves have a low current draw (20mA), enabling relatively small power

supplies to be used. The solenoid coil resistance should be within the range of 1.1k to1.2k ohms.

If outside of this range replace the coil by disconnecting the power wires and puling the solenoid

out of the snap bracket. Replace with a new 20504 Replacement Solenoid Coil.

******Wire polarity is non

specific******

90020504

Replacement

Solenoid Coils

Pulsator Specifications and Servicing

Checking the Solenoid Coil Re-
sistance

Using a Volt meter, turn it on the
ohms (horse shoe)

Check the Resistance between
the outside Black and Red wires.

(SEE DIAGRAM BELOW)

Make sure the resistance range is
correct 1.1k

1.2 k ohms.

STEP TWO

Summary of Contents for Expresso 72560








































































Search results

Summary of Contents for Expresso 72560

Reviews:

Related manuals for Expresso 72560

Brands by name

Popular brands

AIC WAIKATO Expresso 72560, Installation Manual

Search results

Summary of Contents for Expresso 72560

Reviews:

Related manuals for Expresso 72560

Brands by name

Popular brands