AIC WAIKATO Expresso 72560 Installation Manual Download Page 8

Page: 8 / 71

Expresso Tie Stall

(AIC) 608.526.6882

Mounting the Power Supplies

The power supply offered by AIC for
Tie Stall applications is a switching
power supply that has a 120 VAC outlet
plug.

The power supply

’

s input is 120 VAC

and output is 24 VDC 20 amps.

PN. 72540 20 AMP 24VDC Power Supply
Assembly

Always follow local and

national electrical codes.

To Mount the Switcher Power

Supplies:

In all cases the power supply should be
located in clean dry environment.

Find a clean dry environment in the utility
room where the power supply can plug into
the near by a 120 VDC outlet.

Decide where the power supplies will be
located and mount it to a wall where it can
securely fixed.

After the power supply is securely fastened it is
time to wire in the 12 gauge multi

strand 24 VDC

output wire(s).

Never work in the
power supply with

live incoming power.

There are two breakers internally located in the
power supply. Identify the breakers and proceed
wiring in the 24 VDC circuit.

Disclaimer

Hardware Installation

CAUTION

7 Amp 120 VAC

incoming power

breaker.

20 Amp 24 VDC

output power

breaker.

+ 24 VDC

24 VDC

Summary of Contents for Expresso 72560








































































Search results

Summary of Contents for Expresso 72560

Reviews:

Related manuals for Expresso 72560

Brands by name

Popular brands

AIC WAIKATO Expresso 72560, Installation Manual

Search results

Summary of Contents for Expresso 72560

Reviews:

Related manuals for Expresso 72560

Brands by name

Popular brands