AIC WAIKATO Expresso 72560 Installation Manual Download Page 33

Page: 33 / 71

Expresso Tie Stall

(AIC) 608.526.6882

Setup Definitions

Page 7

AIC Waikato Model

When selecting the correct model number and selecting factory defaults

“

Yes

”

and enter the

detacher will automatically change to the model

’

s factory defaults.

Factory Defaults

Factory default settings are for the typical installation. By choosing the

“

Yes

”

in the menu, the

Detacher Control will revert back to all the factory settings as selected by the model number. This

allows the operator to undo all the changes since the Detacher was first installed, and start from

‘

factory

’

settings.

Detacher Control Addressing for Networking

This number establishes the address for the Expresso Stall.

Parlor Size/Number of Detachers connected to the network

This number is total number of detacher controls/stalls in the complete parlor. It tells the Tracker
system how many stalls to look for.

Number of Groups

This number the total number of cow groups being milked. It tells the Tracker software how many

cow groups to set

up for.

Network Speed

Parlor Use Only

Color Style

Selecting Legacy provides the old AIC colors.

Display Style

Legacy or perfect.

Page 8

Time & Date Enter the Local Time

Summary of Contents for Expresso 72560








































































Search results

Summary of Contents for Expresso 72560

Reviews:

Related manuals for Expresso 72560

Brands by name

Popular brands

AIC WAIKATO Expresso 72560, Installation Manual

Search results

Summary of Contents for Expresso 72560

Reviews:

Related manuals for Expresso 72560

Brands by name

Popular brands