AIC WAIKATO Expresso 72560 Installation Manual Download Page 5

Page: 5 / 71

Expresso Tie Stall

(AIC) 608.526.6882

The 72560 Expresso is made to work with 24 VDC power. The PCB output is near the same as

the power supply input. To properly function, the power to the detacher must be within the

operating range of the 24VDC + or –

10%

with NO AC ripple present. To achieve maintaining

this +

10% operating range it is recommend to set the power supply to 26 VDC.

The installer must ensure that the voltage delivered to the stall furthest from the

power supply when fully loaded is adequate in all

circumstances (see above).

It is the installers

’

responsibility to properly regulate the input voltage to achieve the desired

output voltage for the valves used. AIC is not responsible for valve or pulsator coils that may

burn out due to high or low 72560 (MS 34) PC board out voltages.

Ensure that the existing power supplies are of adequate power rating.

AIC is not

responsible for damages or losses incurred by poorly

functioning power supplies. Solid connections are absolutely

necessary to assure no electrical shorts will occur.

*****In all cases, follow local electrical codes and

safety regulations at all times. *****

Do not exceed the manufacturers recommended power ratings

of the power supply used.

When selecting a power supply there may be several alternatives available. A dedicated power

supply is recommended. When connecting to the power supply follow the step by step procedures.

Step 1:

When finding a location to mount the power supply, attention should be given to minimize

the length of the wires connected to the output circuit.

Step 2:

A qualified electrician should install the power supply according to local and national codes.

The power supply should be connected to the incoming power source with a dedicated 240

or 120 VAC circuit.

Step 3:

Locate the output terminals on the power supply.

Step 4:

In tie stall installations, the output power wires will be hooked to the stall cocks.

Step 5:

On 10amp or lower circuits, it is recommended to use no smaller than 14 gauge stranded

wire from the power supply to the stall cocks and the 14 gauge wire looped back to the

power supply. On 10

20amp circuits it is recommended to use no smaller than 12 gauge

stranded wire and the 12 gauge wire looped back to the power supply.

WARNING

CAUTION

Power Supply Specifications

Summary of Contents for Expresso 72560








































































Search results

Summary of Contents for Expresso 72560

Reviews:

Related manuals for Expresso 72560

Brands by name

Popular brands

AIC WAIKATO Expresso 72560, Installation Manual

Search results

Summary of Contents for Expresso 72560

Reviews:

Related manuals for Expresso 72560

Brands by name

Popular brands