AIC WAIKATO Expresso 72560 Installation Manual Download | Manualshive

Page: 18 / 71

background image

Expresso Tie Stall

18 © 2012 Agricultural Instruments Corporation

(AIC) 608.526.6882

BROWSER/GEAR SWITCH After Pressed

1.

REVIEW DATA—After choosing 1 on numeric switch pad, review data, the Expresso will provide
a summary of all the cow milking

’

s stored then when pressing

“

next:

”

will display each individual

cow milking stored.

2.

CHANGE SETTINGS (See the Following Setup Tables)–

After choosing 2 on the numeric switch

pad brings you to the set

-

up pages. There are several pages. To navigate though the settings

press change pages by pressing 9 to move forward and 7 to move back. To select an item press
2 to scroll up and 8 to scroll down. After selecting the item to be changed press switches 4 or 6 to
increase or decrease to the desired value. (See the following Set

-

up Pages)

3.

WRITE TO DATA CARD–

After choosing 3 the Expresso will ask you if you want to write the

stored data onto a data memory card. A card must be present, if no card is present then the
Expresso will tell you there no card present and a card must be added for this to work.

4.

ERASE MEMORY—After choosing 4 the Expresso will ask you erase data (Yes/No) Selecting
Yes will erase the data in memory.

5.

RESET MAINTENANCE

-

After choosing 5 the Expresso will ask you if you want to reset the

maintenance schedule. Internally there is a time clock that tracks the operating hours. This clock
will be reset to zero if yes is selected.

6.

DISPLAY COM STATUS

-

After choosing 6 the Expresso will show the status of the

communication network associated with the system.

7.

EXERCISE OUTPUTS–

After choosing 7 the Expresso allows you to operate the valves by

pressing Cylinder or Milk Line Shut

-

off. This feature allows you to check to be sure the valves

and operating properly.

8.

INITIALIZE WIRELESS—

This setting us used when a wireless module is connected and is used

as a means of identifying the wireless connection included in the unit.

Needs to change.

0: Exit

Switch Operation

All EXPRESSO Tie Stall controls on the installation should be set

-

up the same.

Set

-

up table: To enter set

-

up press the browser (gear) switch. Press 2 to change settings. To navigate

through the set

-

up options press the 2 or 8 switch, when changing a value press the 4 or 6 switch. These

switches have arrows. To page through the setup pages press the 7 or 9 switch. The Expresso will
automatically save the new settings.

Detacher Control Set

-

up

«
...
16
17
18
19
20
...
»

Summary of Contents for Expresso 72560








































































Reviews:

No comments

Related manuals for Expresso 72560

Brand: Parker Research Corp Pages: 3

Brand: S.I.T.A. Pages: 32

Brand: Rainbow Pages: 18

Brand: Mainca Pages: 21

Brand: Daktronics Pages: 30

Brand: DAKOTA ULTRASONICS Pages: 28

Brand: Ransomes Pages: 282

Ransomes HR 6010

Brand: Jacobsen Pages: 10

Brand: Jacto Pages: 64

Brand: Vapotherm Pages: 32

Brand: Vanguard Instruments Pages: 47

Brand: Lalizas Pages: 12

BOBCAT 130 Series

Brand: Balcrank Pages: 12

Optima XR200amx

Brand: GE Pages: 46

GPSMAP 9 3 Series

Brand: Garmin Pages: 222

Wallach UltraFreeze

Brand: Cooper Surgical Pages: 4

Brand: Cuisinart Pages: 159

DJ Laptop stand +tray

Brand: Power Dynamics Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands