AIC WAIKATO Expresso 72560 Installation Manual Download Page 16

Page: 16 / 71

Expresso Tie Stall

(AIC) 608.526.6882

Detacher Set up & Switch Operation

There is a key pad in the decal of the front cover of the EXPRESSO. The key pad has switches
numbered 0

9, two large operating switches pictorially labeled with a hand by the left (manual/wash)

switch and an udder w/milker unit by the right (attach/detach) switch and three actuator switches
labeled with a check mark, X and gear/browser icon.

Key Pad Layout

Switch Operation

Milk, Manual/Wash Switches

When Milking

—The milk and manual switches are used during normal milking. To start milking

press the milk switch. If user detach is desired press the milk switch again. To override automatic
detach press the manual switch. The red lights will flash to remind the operator the detacher is in the
manual milking mode.

Continue

—If the detacher detaches prematurely and it is desired to

“

continue

”

the milking record for

the same cow, press the manual switch then the milk switch, attach the milking unit and the milking
record will continue from where it left off.

Wash

—To enter the wash mode press and hold the manual/wash switch for 3 seconds.

NUMERIC SWITCHES

0 = ARE USED TO

ADD COW

NUMBERS,CHANGE

GROUPS, SORT AND

NAVEGATE

ATTACH/DETACH

(Milk Switch)

MANUAL/WASH

ACCEPT
SWITCH = CHECK
MARK

BROWSER SWITCH

DELETE SWITCH =

Summary of Contents for Expresso 72560








































































Search results

Summary of Contents for Expresso 72560

Reviews:

Related manuals for Expresso 72560

Brands by name

Popular brands

AIC WAIKATO Expresso 72560, Installation Manual

Search results

Summary of Contents for Expresso 72560

Reviews:

Related manuals for Expresso 72560

Brands by name

Popular brands