ADT Enterpreneur 3000EN, Installation And Setup Manual

Page: 49 / 104

4-15
Configurable Zone Type Charts
ENTRY 1 ENTRY 2
Response when system disarmed and zone is:
Intact EOL
RF zone normal
Open
RF zone N/A
Shorted
RF zn off-normal
Auto
Restore Vent Zone
0 = normal
1 = alarm
2 = trouble
3 = fault 0 = normal
4 = alarm
8 = trouble
12 = fault
see note 5
0 = normal
1 = alarm
2 = trouble
3 = fault 0 = no
4 = yes 0 = no
8 = yes
Entry 1 = EOL + Open Entry 2 = Short + auto r vent zone
ENTRY 3 ENTRY 4
Response when armed STAY and zone is:
Intact EOL
RF zone normal
Open
RF zone N/A
Shorted
RF zn off-normal
Byp. when
disarmed
Byp. when
armed
0 = normal
1 = alarm
2 = trouble
3 = fault 0 = normal
4 = alarm
8 = trouble
12 = fault
see note 5
0 = normal
1 = alarm
2 = trouble
3 = fault 0 = no
4 = yes 0 = no
8 = yes
Entry 3 = EOL + Open Entry 4 = Short + byp. di byp. armed
ENTRY 5 ENTRY 6
Response when armed AWAY and zone is:
Intact EOL
RF zone normal
Open
RF zone N/A
Shorted
RF zn off-normal
Dial Delay
(see field *50)
Fault Delay
(see field *53)
0 = normal
1 = alarm
2 = trouble
3 = fault 0 = normal
4 = alarm
8 = trouble
12 = fault
see note 5 0 = normal
1 = alarm
2 = trouble
3 = fault 0 = no
4 = use delay 0 = no
8 = use delay
see note 1
Entry 5 = EOL + Open Entry 6 = Short + dial delay + fault delay
ENTRY 7 ENTRY 8
Display Faults Power Reset/
Verification
Use Entry
Delay 1/2
Use Exit
Delay
Respond as
Interior Type
0 = show alarms
when armed
& disarmed
1 = don’t show
alarms when
armed
(show
alarms, trbles,
faults when
disarmed)
3 = never show
any alarms,
trbles, faults
0 = no
4 = power reset
after fault
(with code + OFF)
12 = verification
(see
zone
type 16)
0 = no
1 = delay 1
2 = delay 2 0 = no
4 = use exit
delay
0 = no
8 = yes
see note 2
Entry 7 = fault d power
reset/verification Entry 8 = entry delay 1/entry delay 2 + exit delay +
interior zone type
ENTRY 9 ENTRY 10
Alarm Sounds Use Bell
Timeout Respond as
Fire Zone
Trouble
Sounds Chime when Chime
Mode On
0 = none
1 = steady
touchpad
2 = steady bell
and
touchpad
3 = pulsing bell
and
touchpad
0 = no
4 = yes
see fields *32,
*33 0 = no
8 = yes
see zone type
09; see note 4 0 = none
1 = periodic
beep
2 = trouble
beeps
0 = no
4 = yes
Entry 9 = alarm bell t fire zone Entry 10 = trouble chime
OPEN SHORTED INTACT
EOL
ADT3000-018-V0
Zone Conditions Represented
in Entries 1-6
Configurable Zone Type Notes
1. Do not use the “fault delay” option
with a configurable zone type if it
is set for an entry or exit delay,
otherwise unpredictable results
may occur.
2. To create an interior type zone,
select “respond as interior zone
type” (entry 8, interior type = yes),
and set zone response to “fault” in
entries 3-4 to ensure fault displays;
do not set as “normal,” “alarm,” or
“trouble.”
3. Do not set fire zones to respond as
a “fault” (entries 1-6), otherwise
faults will not display unless the
[
∗
] key is pressed.
4. 4219/4229 modules must use
EOLRs or unpredictable results
may occur.
5. RF ZONE NOTE: The “open”
options in entries 1, 3, and 5 are
not applicable for RF zones. Use
the “intact EOL” option for normal
RF zone conditions and “shorted”
for off-normal RF zone conditions.