ADT Enterpreneur 3000EN, Installation And Setup Manual

Page: 44 / 104

3000EN Series: Installation Instructions
4-10
*93
No. of Reports In Armed Period
per Zone (Swinger Suppression)
Entry 1: No. of Report Pairs
1 = 1 report pair per zone per armed
period
2 = 2 report pairs per zone per armed
period
Entry 2 (SIA Installations) : Unlimited
Reports Enable
0 = restrict reports to the setting in
entry 1
1 = unlimited reports for zones listed in
zone list 7
This option can be used to limit the number of alarm/alarm
restore message pairs per zone sent to the central station in
an armed period. Swinger suppression applies to burglary
zones only.
Use entry 1 to limit reports to one or two report pairs as
desired, or use entry 2 for zones that require unlimited
reporting; these zones ignore the setting in entry 1. If
selected, enter appropriate zones in zone list 7.
SIA installations: Entry 1 must be set for option 1 or 2.
*94
Download Phone Number
Enter up to 20 digits as follows: 0–9, #
+11 for “
∗
”, # + 12 for “#”, # + 13 for a
pause.
Enter the phone number of the downloading computer.
Do not fill unused spaces. End field by entering
∗
. To clear
entries from field, press
∗
94
∗
.
Field *
UL
Downloading may be performed only if a technician is at the site.
*95
Ring Count For Downloading
0–15 = number of rings before control
picks up phone line .
† NOTE: If “15” is entered to bypass
an answering machine, and a 4286
Phone Module is included in the
system, you should note the
following:
When calling in from an off-
premises phone, the user should
make the initial call, allow 1 or 2
rings only, then hang up. The user
should then call again. The phone
module will now seize the line, and
2 long tones sound, followed by the
usual voice prompt for the access
code. If this procedure is not
followed, phone module operation
will not be possible.
Refer to the chart below and program this field accordingly.
phone answer down-
module machine loading Set
field
∗∗∗∗
95 to…
yes no no 1-14 (not 0)
yes yes no greater than rings set on
answer machine (e.g., if ans.
machine is 4 rings, set this
field to 5). This allows access
to the phone module if the
answer machine is turned off.
yes no yes 1-14 (not 0)
yes yes yes 15 (bypasses answer
machine)†
no no no 0
no yes no 0
no no yes 1-14
no yes yes 15
*96
Command to Initialize CSID and
Subscriber Account Number This is a command function, not a data field. Use this
command, if necessary, to reset all subscriber account
numbers and the internal CSID to the factory default values.
*97
Command to Reset System to
Factory Default Values This is a command function, not a data field. Pressing
∗
97
resets all data fields to the factory default values (shown on
the Program Form).
IMPORTANT: Do not press
∗
97 to load defaults if any
programming has been done previously—data already
programmed into the system will be changed!
*98
Command to Exit Program Mode
(with installer code lockout) Exits Programming Mode and prevents re-entry by:
Installer Code + [8] + [0] + [0]. To enter the programming
mode if
∗
98 was used to exit, you must first power the system
down. Then power up again, and press [
∗
] and [#] at the same
time, within 50 seconds of powering up.
*99
Command to Exit Program Mode Exits Programming Mode and allows re-entry by:
Installer Code + [ 8] + [0] + [0] or by: Pressing [
∗
] and [#] at
the same time, within 50 seconds of power-up.