3000EN Series: Installation Instructions
3-6
AVS QUICK PROGRAMMING COMMANDS (for AAV sessions using the AVS-ADT system)
For controls with the firmware revision level 7.0 or higher, these commands automatically configure the control
for AVS operation.
•
installer code + [#] + [0] + 3
: enable AVS operation
•
installer code + [#] + [0] + 4
: enable AVS operation and enable panels sounds on the AVST-ADT speaker
•
installer code + [#] + [0] + 5
: remove all programming options set by [#] + [0] + 3 quick command
•
installer code + [#] + [0] + 6
: remove all programming options set by [#] + [0] + 4 quick command
Refer to the AVS SYSTEM ENABLE section for details on the specific options that are set with each command,
depending on the control used.
To select the AAV session communication path (phone line/communication device), see field
∗
55 Dynamic
Signaling Priority.
To enable AAV operation, use
∗
91 Options field (option 4).
Loading Factory Defaults/Initializing for Download
To Load Default Entries
Press
∗
97 while in Program Mode. This resets all data fields to the ADT
default values shown on the Program Form. Use
∗
97 only if you wish to
return to the original factory-programmed defaults.
To Initialize Download ID
Press
∗
96 while in Program Mode. This initializes the system for
downloading and resets all the subscriber account numbers and CSID.
IMPORTANT:
Do not press
✱
97 to load defaults if any programming has been done previously—data already
programmed into the system will be changed!
Exiting the Programming Mode
Prevent installer code reentry
Press
∗
98. Exits Programming Mode and prevents re-entry by:
Installer Code + [8] + [0] + [0]. To enter the programming mode if
∗
98 was
used to exit, you must first power the system down. Then power up again,
and press [
∗
] and [#] at the same time, within 50 seconds of powering up.
Allow installer code reentry
Press
∗
99. Exits Programming Mode and allows re-entry by:
Installer Code + [ 8] + [0] + [0] or by: Pressing [
∗
] and [#] at the same time,
within 50 seconds of power-up.
Table of Device Addresses
This Device
Uses
Address
Reports as
†
Enabled By…
RF Receiver
00
100
*56 zone programming: input device type entry
AUI 1
01
n/a
††
automatic if AUI enable field *189 enabled for AUI 1
AUI 2
02
n/a
automatic if AUI enable field *189 enabled for AUI 2
AUI 3
05
n/a
automatic if AUI enable field *189 enabled for AUI 3
AUI 4
06
n/a
automatic if AUI enable field *189 enabled for AUI 4
Communication Device (LRR)
03
103
automatic if communication device enabled in menu mode
∗
29
4286 Voice Module
04
104
automatic if phone module access code field *28 enabled
Zone Expanders (4219/4229):
module 1 (for zones 09 - 16)
module 2 (for zones 17 - 24)
module 3 (for zones 25 - 32)
module 4 (for zones 33 - 40)
module 5 (for zones 41 - 48)
07
08
09
10
11
107
108
109
110
111
*56 zone programming: input device type, entry 2, then:
automatic if zone no. 9-16 entered as AW type or relay assigned
automatic if zone no. 17-24 entered as AW type or relay assigned
automatic if zone no. 25-32 entered as AW type or relay assigned
automatic if zone no. 33-40 entered as AW type or relay assigned
automatic if zone no. 41-48 entered as AW type or relay assigned
Relay Modules (4204):
module 1
module 2
module 3
module 4
12
13
14
15
112
113
114
115
*79 output device programming: device address prompt:
entered at device address prompt
entered at device address prompt
entered at device address prompt
entered at device address prompt
Touchpads:
touchpad 1
touchpad 2
touchpad 3
touchpad 4
touchpad 5
touchpad 6
touchpad 7
touchpad 8
16
17
18
19
20
21
22
23
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
data field programming as listed below:
always enabled for partition 1, all sounds enabled.
data field *190
data field *191
data field *192
data field *193
data field *194
data field *195
data field *196
HSPIM Module
25
n/a
automatic
5800TM Module
28
n/a
automatic
††
Addressable devices are identified by “1” plus the
device address when reporting. Enter report code for
zone 91 to enable device reporting (default = enabled).
See field *199 for addressable device (ECP) 3-digit/2-
digit identification touchpad display options.
Summary of Contents for Enterpreneur 3000EN
