background image

ABB | SACE Tmax XT

48 | © 2019 ABB |  1SDH002039A1002 - ECN000093027 - Rev. A

Protections | 1 - Standard Protections

Harmonic distortion

Allows an alarm to be activated in the case of distorted wavefoms.
The protection can be enabled in the 

Measurements

 menu; if enabled an alarm is activated (page 32).

 

IMPORTANT: the protection does not handle the trip, just the signal

T Protection

T protection protects against abnormal temperatures recorded by the unit.
It is always activated and invoves two statuses, depending on the temperature reading:

State

Temperature range [°C]

Ekip Touch actions

Warnings

-40 < t < -25 or 70 < t < 85

Display off; Warning led on @ 0.5 Hz

Alarm

t < -40 or t > 85

Display off; Alarm and Warning leds on @ 2 Hz

The Trip Enabling parameter can be enabled in the 

Settings

 - 

Circuit breaker

 menu in order to handle an open 

command if an alarm occurs (page 33).

Hardware Trip

Hardware Trip protects against connection errors in Ekip Touch and is available in the 

Settings

 - 

Circuit 

breaker

 - 

Hardware Trip

 menu (page 32).

If enabled, if one or more of these events are detected:

•  current sensors disconnected (phase or external if enabled)
• 

Rating Plug

 disconnected.

• 

Trip Coil

 disconnected

•  faults inside the unit

alarm is signaled and an open command is transmitted.

 IMPORTANT:

•  the protection trips if the error statuses persist for more than one second
•  only signaling is managed if an alarm occurs due to Trip coil disconnection

 

Summary of Contents for SACE Tmax XT5














































































































































































































Reviews: