background image

ABB | SACE Tmax XT

Internal accessories | 7 - Ekip Com Hub

191 | © 2019 ABB |  1SDH002039A1002 - ECN000093027 - Rev. A

7 - Ekip Com Hub

 

Ekip Com Hub

 is a communication accessory that enables the data and measurements of Ekip Touch and 

other devices connected to the same installation to be gathered and then made available on the server 
through an Ethernet network.
The configuration of the module is available via Ekip Connect or with the System Interface document, which 
contains all the details. (page 129).
The ports used by the module are:

Port

Service

Notes

67/UDP 68/UDP

DHCP client

DHCP client enabled as an alternative to 

Static address

 =  

On

443/TCP

HTTPS

always active when module is enabled

123/TCP

SNTP

active with SNTP client enabled

53/TCP

DNS

always active

Ekip Link

 also provides information about the status of the circuit-breaker (open, closed, tripped).

 

IMPORTANT: each circuit-breaker can house one module only; configuration with 
external communication modules is not allowed if an internal module is present.

Safety and cyber security

The module uses the HTTPS protocol and can be connected to the Internet

 IMPORTANT:

• 

it is the customer's sole responsibility to provide and continuously ensure a secure 
connection between the module and customer network or any other network (as the 
case may be). The plant manager must establish and maintain appropriate measures 
(such as but not limited to the installation of firewalls, application of authentication 
measures, encryption of data, installation of antivirus programs, etc.) to protect the 
product, the network, the customer system and interface against any kind of security 
breaches, unauthorized access, interference, intrusion, loss and/or theft of data or 
information.ABB and its affiliates are not liable for damages and/or losses related to 
such security breaches, unauthorized accesses, interference, intrusion, loss and/or 
theft of data or information.

Connections

To connect the module to its communication network and for references about the terminals, please consult 
circuit diagrams 

1SDM000005A1001

.

The module is supplied with a 1-meter length cable and cabled RJ45 connector for interfacing with its 
network.
To connect the module to Ekip Touch and to actuator MOE-E if present, please consult document 

1SDH002011A1503

.

 

Summary of Contents for SACE Tmax XT5














































































































































































































Reviews: