ABB SACE Tmax XT5 Operation And Maintenance Manual Download Page 15 | Manualshive

Page: 15 / 205

ABB SACE Tmax XT5 Operation And Maintenance Manual Download Page 15

ABB | SACE Tmax XT

Overview of Ekip Touch | 3 - Accessories and software

13 | © 2019 ABB | 1SDH002039A1002 - ECN000093027 - Rev. A

3 - Accessories and software

External accessories

The functions of Ekip Touch can be expanded by further accessories and external modules, which differ as
to function and assembly method.
The main external modules are:

Name

Function

Page

Ekip Supply

Power supply

Ekip Com

Communication (with various protocols)

Ekip Link

Communication via intranet with ABB proprietary protocol

Ekip Signalling 2K

Signalling with inputs/outputs

Ekip Signalling 3T

Signalling with analog inputs

Ekip Synchrocheck

Voltage measurement and synchronism between two supply
sources

Ekip CI

Command module for motor applications

These moduoles must always be connected to the Trip unit using the Elip Cartridge DIN Rail accessory and
only if there are no internal accessories present (page 130).
Other external modules and accessories, available with direct connections to the internal terminal box or rear
connectors, are:

Name

Function

Page

Ekip Signalling 10K

Signalling with inputs/outputs

Ekip Multimeter

Panel front display

External neutral

Neutral protection with 3P CB

In addition, the supervision, configuration and reporting functions are provided by further modules for
temporary communication and supply:

Name

Function

Page

Ekip TT

Supply and tests

Ekip T&P

Supply, communication, programming and tests

Ekip Programming

Supply, communication and programming

Ekip Bluetooth Key

Bluetooth communication and programming

Internal accessories

The SACE XT5 circuit-breaker has a compartment for connection certain internal modules to the Trip unit:

Name

Function

Page

Ekip Com

Communication (various protocols)

Ekip Signalling 1K

Signalling with inputs/outputs

Ekip Maintanance

Signalling with inputs/outputs

Micro I/O

CB status signaling

These modules connect to the Trip unit directly to the internal terminal box and only if there are no external
accessories (with the exclusion of Ekip Signalling 10K, Ekip Multimeter and External neutral).

Additional functions

Ekip Touch can be equipped with further software configurations compliant with different functional
applications:

•  Power Controller
•  Load Shedding
•  Interface protections (IPS)
•  Synchro reclosing
•  Embedded ATS

For details consult the

Technical catalog

(page 4) or the summary documents of each function (page 14).

«
...
13
14
15
16
17
...
»

Summary of Contents for SACE Tmax XT5














































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands