ABB SACE Tmax XT5 Page 194 Operation And Maintenance Manual Download | Manualshive

Page: 194 / 205

background image

ABB | SACE Tmax XT

192 | © 2019 ABB | 1SDH002039A1002 - ECN000093027 - Rev. A

Internal accessories | 7 - Ekip Com Hub

Power supply

Ekip Com Hub is supplied directly by the

Ekip Touch

to which it is connected.

NOTE:

communication between Ekip Touch and the module is interrupted in the absence of

auxiliary power supply

Configurations via menu

Local bus activation, which is essential for starting the communication between module and Ekip Touch, is
available in the

Settings

menu (page 33).

The following communication parameters can be configured if the module has been correctly detected by
Ekip Touch in the

Settings

-

Modules

menu:

Parameter

Description

Default

Enable

Switches communication between module and server on/off.

Force Static IP
Address ON

Defines whether the module has the dynamic (Off) or static (

On

) IP

address.
If =

On

all the associated parameters are enabled

Off

Static address
IP address

Enables the static IP to be selected

0.0.0.0

Static Network
Mask

Enables the subnet mask to be selected

0.0.0.0

Static Gateway
address

When there are several subnets, enables the IP address of the node to
which the module is connected to be selected

0.0.0.0

Enable SNTP
client

Allows the SNTP protocol for distribution of the clock and
synchronization signal to be enabled.

Off

SNTP Server
Addr.

Allows the network server that supplies the SNTP to be set.

0.0.0.0

Password

code required to register module on Cloud

---

Remote
firmware update

Enables the firmware of the module to be updated. There are two
parameters:
•

Enable

, to configure firmware download

•

Automatic

, to automate module updating

Off
Automatic

Information in menu

The following information will be available in the

About

-

Modules

menu if Ekip Touch has detected the module

correctly:

Information

Description

SN and version

Identifier and SW version of the module

IP address

Address of the module, assigned to the module by a DHCP server at the time of
connection to the network in the case of configuration with a dynamic IP, or can be
set via the menu in the event of a static IP.

NOTE:

without a DHCP server, the module automatically adopts a random IP

address within the 169.254.xxx.xxx

range

Network Mask

Subnet mask; identifies the method for recognizing the subnet to which the modules
belong and enables modules to be searched for within a defined set of recipients.

Gateway address

IP address of the node to which the module is connected, in the presence of several
subnets

MAC address

Address assigned by ABB, with OUI (Organizationally Unique Identifier) equal to
ac:d3:64, which uniquely identifies the manufacturer of an Ethernet device

«
...
192
193
194
195
196
...
»

Summary of Contents for SACE Tmax XT5














































































































































































































Reviews:

No comments

Related manuals for SACE Tmax XT5

Brand: Eaton Pages: 3

Brand: Eaton Pages: 2

Brand: Eaton Pages: 10

Brand: GE Pages: 76

U-POWER Omega UW-MTX 1.5G

Brand: Larsen & Toubro Pages: 149

Brand: ABB Pages: 56

Brand: DACO Pages: 48

Brand: PCE Health and Fitness Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands