manualshive.com logo in svg

ABB SACE Tmax XT5, Operation And Maintenance Manual

Share
Download
ABB SACE Tmax XT5 Operation And Maintenance Manual Download Page 195

ABB | SACE Tmax XT

Internal accessories | 7 - Ekip Com Hub

193 | © 2019 ABB |  1SDH002039A1002 - ECN000093027 - Rev. A

Remote configurations

Additional parameters can be accessed via the service connector (via Ekip Connect) or via a system bus 
communication:

Information

Description

CRL Enable

Allows the CRL (Certificate Revocation List) to be used to ascertain whether the 
server certificate is valid

Clock update 
hardening enable

Enables control of the time reference transmitted by the SNTP server

SNTP Server 
Location

Enables the position of the SNTP server to be set in relation to the network in which 
the module is installed

SNTP Time zone

Defines the time zone to be used for synchronism

SNTP Daylight 
Saving Time

Used to select whether daylight saving time is present (ON) or not (OFF) in the 
country to which the synchronization time refers

Disable Gratuitous 
ARP

Permits (Enabled ARP) the periodic generation of a Gratuituos ARP message, used 
by Ekip Connect to rapidly find the modules via Ethernet scan without knowing the 
IP address beforehand

Remote information

Additional information can be accessed via the service connector (via Ekip Connect) or via a system bus 
communication:

Information

Description

HW and Boot version

general module information

Flash CRC status and 
result

Information about the correctness of the SW in the module

Publish enable 
configuration

Enable status in 

Security File

Configuration file

Name of the file dedicated to the information to transmit (measurements, etc.)

Security file

Name of the file dedicated to the information requested by the module for 
transmission purposes (addresses, certificates, etc.)

Certificate Revocation 
List

name of file containing revoked certificates

Executable file

name of the executable firmware update file

Configuration error

error status of module configuration

Sample time

period of data acquisition from the connected devices

Log time

period within which the acquired data are saved in the log

Upload time

period (calculated by the module) between each data transmission

Configured device

Number of modules involved in the network with Hub module

Polling period API events

period with which the module communicates with the API device

Connection client 1, 2, 3

Address of TCP modbus clients connected to the module

Statistics

Recordings of the latest saving operations and percentage of resources being 
used

Status plant side

Information about the quality of the communication with the other devices

Status Cloud side

State of the errors concerning the TLS session established between module 
and server

Application status

operation progress indicators

Status

General indicators of the module: SNTP status, flash, cable connection, FW 
availability, file errors, etc.

 

Summary of Contents for SACE Tmax XT5














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands