ABB SACE Tmax XT5 Operation And Maintenance Manual Download | Manualshive

Page: 160 / 205

background image

ABB | SACE Tmax XT

158 | © 2019 ABB | 1SDH002039A1002 - ECN000093027 - Rev. A

External accessories | 12 - Ekip Com Hub

Interface

the module has three signaling leds:

1

2

Figure 51

LEDs

Description

Power

Signals the on status and correct communication with Ekip Touch:
• off: module off
• on steady or flashing synchronized with the Power led of Ekip Touch: module on
and communication with Trip unit present.
• flashing not synchronized with the Power led of Ekip Touch (2 fast flashes per
second): module on and communication with Trip unit absent.

Link (

1

)

Indicates the communication state:
• off: incorrect connection, signal absent.
• on steady: connection correct

Activity (

2

)

Indicates the communication state:
• off: no activity on line
• flashing: activity on line present (receiving and/or transmitting)

Configurations via menu

Local bus activation, which is essential for starting the communication between module and Ekip Touch, is
available in the

Settings

menu (page 33).

The following communication parameters can be configured if the module has been correctly detected by
Ekip Touch in the

Settings

-

Modules

menu:

Parameter

Description

Default

Enable

Switches communication between module and server on/off.

Force Static IP Address
ON

Defines whether the module has the dynamic (Off) or static (

On

)

IP address.
If =

On

all the associated parameters are enabled

Off

Static address IP address

Enables the static IP to be selected

0.0.0.0

Static Network Mask

Enables the subnet mask to be selected

0.0.0.0

Static Gateway address

When there are several subnets, enables the IP address of the
node to which the module is connected to be selected

0.0.0.0

Enable SNTP client

Allows the SNTP protocol for distribution of the clock and
synchronization signal to be enabled.

Off

SNTP Server Addr.

Allows the network server that supplies the SNTP to be set.

0.0.0.0

Password

code required to register module on Cloud

---

Remote firmware update

Enables the firmware of the module to be updated. There are two
parameters:
•

Enable

, to configure firmware download

•

Automatic

, to automate module updating

Off
Automatic

«
...
158
159
160
161
162
...
»

Summary of Contents for SACE Tmax XT5














































































































































































































Reviews:

No comments

Related manuals for SACE Tmax XT5

Brand: Siemens Pages: 2

Brand: Siemens Pages: 2

Brand: Siemens Pages: 2

Brand: Siemens Pages: 2

Brand: Siemens Pages: 4

Brand: Siemens Pages: 8

Brand: Eaton Pages: 3

Brand: Eaton Pages: 2

Cutler-Hammer DSII Series

Brand: Eaton Pages: 66

Brand: GE Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands