background image

ABB | SACE Tmax XT

Electronic accessories | 1 - Rating Plug

127 | © 2019 ABB |  1SDH002039A1002 - ECN000093027 - Rev. A

Electronic accessories

1 - Rating Plug

 

The 

Rating Plug

, supplied with Ekip Touch, establishes the rated current In required by the measuring range 

and sets the current protections (with reference to In).
It is installed on a dedicated front connector which can be accessed by the user.
The trip unit continuously checks for the presence of the 

Rating Plug

 and signals its absence or any assembly 

or installation errors.
If a new model is installed, Ekip Touch displays the request for installation when first powered.
Field 

Nom.Curr

 in the 

About

-

Circuit breaker

 menu displays the In quantity read by the unit.

Replacement

The module can be replaced by the user; any 

Rating Plug

 with maximum rated current equal to the nominal 

size of the CB (Iu) can be installed.

 WARNING!

• 

models up to 250A at 400A can be installed if the original Rating Plug is 400A or less

• 

models up to 250A at 630A can be installed if the original Rating Plug is 500A or 630A

Further details about assembly and the Rating Plug installation procedure are available in ABB Library, 
particularly in document 

1SDH002011A1505

.

 

IMPORTANT: to avoid alarms or undesired trips, the Rating Plug must be replaced 
when Ekip Touch is off, the CB open and in the absence of primary currents and 
voltages

 

Summary of Contents for SACE Tmax XT5














































































































































































































Reviews: