ABB SACE Tmax XT5 Operation And Maintenance Manual Download | Manualshive

Page: 48 / 205

background image

ABB | SACE Tmax XT

46 | © 2019 ABB | 1SDH002039A1002 - ECN000093027 - Rev. A

Protections | 1 - Standard Protections

2I Protection

2I

I31

t

I

Function

If the current of one or more phases exceeds threshold I31 and a trip event is present, the protection
transmits the TRIP command after a non-programmable fixed time.
To check and simulate the trip times in relation to all the parameters, please consult:

• summary table of the protections with the operating characteristics (page 79)
• the graph with trip curve (page 86)

Parameter

Description

Default

Enable

Activates/deactivates the protection and its availability in the
parameters menu.

OFF

Threshold I31

Establishes the value that activates the protection.
The value is given as both absolute value (A) and relative value (In) and
can be set within the range: 1.5 In to 15 In, in 0.1 In steps

1,5 In

Protection enabling makes the

2I Mode

section available in the

Advanced - Functions

menu, where the

protection activation event can be configured:

Parameter

Description

Default

Activation

Two alternative modes are available:
• Dependent function: the protection is activated if the programmed
activation event has occurred; this configuration makes the function
and delay parameters available
• Activated: the protection is always activated

Dependent
function

Function

The activation event between the input contacts of Ekip Signalling 2K,
the statuses of the unit (open/closed) and the Custom function can be
selected

NOTE

: Ekip Connect allows the Custom function to be

customized so as to associate the activation event with up to
eight statuses in AND or OR configuration

Disabled

Delay

Protection activation delay calculated from the presence of the
activation event onwards.
The value is given in seconds and can be set within the range: 0 s to
100 s, in 0.1 s steps

NOTE

: the protection trips if the event is present for longer than

the set time lag

0 s

Commands by remote control

Two further temporary protection activation/deactivation commands are available when the unit is connected
to one or more Ekip Com modules:

•

2I ON Mode

: activates the protection

•

2I OFF Mode

: deactivates the protection

Consult the unit System Interface 1SDH002031A1101 for details.

NOTE:

if the protection has been activated by command 2I ON Mode, it is deactivated by

command 2I OFF Mode or when the unit shuts down

Signallings

When protection 2I is activated, the message “

2I active

” appears in the diagnostic bar and in the Alarm List

page, and the alarm led will be on steady.

«
...
46
47
48
49
50
...
»

Summary of Contents for SACE Tmax XT5














































































































































































































Reviews:

No comments

Related manuals for SACE Tmax XT5

Brand: KING Pages: 4

PRO SERIES THE MAESTRO

Brand: Power Probe Tek Pages: 31

Brand: TAVRIDA ELECTRIC Pages: 172

Brand: IFM Pages: 12

Brand: ABB Pages: 109

Brand: Siemens Pages: 3

Brand: Siemens Pages: 2

Brand: Schaltbau Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands