ABB SACE Tmax XT5 Page 34 Operation And Maintenance Manual Download

Page: 34 / 205

ABB | SACE Tmax XT

Interface and menus | 4 - Menu

Measurements Menu

Submenus

Description

Page

Historicals

Trip

Description in dedicated chapter

Events

List of events recorded

Measurements

List and description in dedicated
chapter

Power factor

(1)

Power factor measurement

101

Frequency

(1)

Frequency measured

101

Energy

(1)

Energy counters

Measurement of energies

101

Reset counters

Meter reset command

Energy RESET

List and description in dedicated
chapter

101

Peak factor

(1)

Peak factor of each phase

101

Harmonic dist.

Activation command for current
harmonic distortion monitoring

Ekip
Synchrocheck

(2)

Description in dedicated chapter

167

Network
Analyzer

(3)

V Sequences

Measurements associated with
Network Analyzer function: list and
description in dedicated chapter

107

3s V Sequences
THD Current
THD Voltages
Counters
Waveforms

Maintenance

Contact Wear

Installation and maintenance dates
and commands

117

LastServiceContactWear
Installation
Last Maintenance
Service RESET

(1)

available if provided for by Trip unit model or if SW Measuring Measurements package has been activated

(2)

available when Ekip Synchrocheck module is present

(3)

available if provided for by Trip unit model or if Network Analyzer SW package has been activated

Summary of Contents for SACE Tmax XT5














































































































































































































Search results

Summary of Contents for SACE Tmax XT5

Reviews:

Related manuals for SACE Tmax XT5

Brands by name

Popular brands

ABB SACE Tmax XT5, Operation And Maintenance Manual

Search results

Summary of Contents for SACE Tmax XT5

Reviews:

Related manuals for SACE Tmax XT5

Brands by name

Popular brands