ABB DressPack IRB6650S Product Manual Download Page 51

Page: 51 / 390

2.2.4.2 Fitting the attachments of IRBDP MH2 LI

Location

The location of the attachments of the cable package IRBDP MH2 LI is shown in
the figure.

The figure shows IRBDP MH2 LI fitted on IRB 6600 but the principle assembly is
the same on IRB 7600 and 6650S.

xx1000000099

Cable bracket (IRB 6650S)

Cable bracket (IRB 7600). Already fitted on the cable package when delivered.

Required equipment

Note

Art. no.

Equipment

Loctite 243

3HAB7116-1

Locking liquid

For locking screws securing brackets
and connection plate.

The contents are defined in section

Toolkits, DressPack/SpotPack on
page 355

3HAC17290-7

Standard toolkit,
DressPack/SpotPack

These procedures include references
to the tools required.

Other tools and procedures may
be required. See references to
these procedures in the step-by-
step instructions below.

Continues on next page

Product manual - DressPack/SpotPack IRB 6650S

3HAC055424-001 Revision: C

2 Installation

2.2.4.2 Fitting the attachments of IRBDP MH2 LI

Summary of Contents for DressPack IRB6650S






































































































































































































































































































































































































Search results

Summary of Contents for DressPack IRB6650S

Reviews:

Brands by name

Popular brands

ABB DressPack IRB6650S, Product Manual

Search results

Summary of Contents for DressPack IRB6650S

Reviews:

Brands by name

Popular brands