ABB DressPack IRB6650S Product Manual Download Page 48

Page: 48 / 390

2.2.4 Installation of IRBDP MH1 LI and IRBDP MH2 LI

2.2.4.1 Fitting the attachments of the IRBDP MH1 LI

Location

The location of the attachments of the cable packages IRBDP MH1 LI are shown
in the figure.

The figure shows the internal IRBDP MH1 LI fitted on IRB 6600 but the principle
assembly is the same on IRB 7600 and 6650S.

xx1000000098

Cable bracket (IRB 6650S).

Cable bracket (IRB 7600). Already fitted on the cable package when delivered.

Required tools

Note

Article number

Equipment

The contents are defined in sec-
tion

Toolkits, DressPack/Spot-

Pack on page 355

3HAC17290-7

Standard toolkit, DressPack/Spot-
Pack

Required spare parts

Note

Article number

Spare part

See

DressPack for lower arm MH

- IRBDP MH1 LI on page 361

Material set cable package IRBDP
MH1 LI

Continues on next page

Product manual - DressPack/SpotPack IRB 6650S

3HAC055424-001 Revision: C

2 Installation

2.2.4.1 Fitting the attachments of the IRBDP MH1 LI

Summary of Contents for DressPack IRB6650S






































































































































































































































































































































































































Search results

Summary of Contents for DressPack IRB6650S

Reviews:

Brands by name

Popular brands

ABB DressPack IRB6650S, Product Manual

Search results

Summary of Contents for DressPack IRB6650S

Reviews:

Brands by name

Popular brands