manualshive.com logo in svg

ABB DressPack IRB6650S, Product Manual

Share
Download
ABB DressPack IRB6650S Product Manual Download Page 311

Note

Action

xx1500000905

Put the clamp jaw in the ball joint housing.

10

Refit the front part protection hose

Note

Action

A

xx0300000061

Top of a ridge

A

Length: 950 mm

Cut the protection hose, front part, to the length
required.

Note

Place the cut on top of a ridge.

1

Carefully push cables and hoses into the protec-
tion hose.

Tip

The following order is preferred:

1

Cables with large connectors

2

Hoses

3

Cables with small connectors

2

Make sure that cables and hoses are not twisted.

3

xx1400000350

Fit the middle jaws in one of the hose reinforce-
ment funnel halves.

Note

The side of the hose reinforcement funnel that
has the bigger outer diameter shall be turned to-
wards the wrist.

4

Fit the other half of the funnel.

5

Continues on next page

Product manual - DressPack/SpotPack IRB 6650S

311

3HAC055424-001 Revision: C

© Copyright 2004-2018 ABB. All rights reserved.

4 Repair

4.2.15 Replacing the protection hose - IRBDP SW6 UI and MH6 UI

Continued

Summary of Contents for DressPack IRB6650S







































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands