ABB DressPack IRB6650S Product Manual Download Page 323

Page: 323 / 390

Adjusting the spring force and securing the spring

Note

Action

xx0500001562

Use the wrench to adjust appropriate spring
force. Carefully lower the spring if needed.
To

increase

the force: pull the wrench back-

ward.
To

decrease

the force: push the wrench for-

ward.

View:

A Showing the spring with no

tension

B Showing the spring with ¾ ten-

sion (270°).

View of inside.

xx0500001509

Secure the spring force by lifting up the spring
and fit into hole circle.
The spring could be set in steps of 1/8 of a turn.

A Guide pins

Tip

The next step is best performed by two persons
working together.

Continues on next page

Product manual - DressPack/SpotPack IRB 6650S

323

3HAC055424-001 Revision: C

4 Repair

4.2.17 Adjusting tension arm unit

Continued

Summary of Contents for DressPack IRB6650S






































































































































































































































































































































































































Search results

Summary of Contents for DressPack IRB6650S

Reviews:

Brands by name

Popular brands

ABB DressPack IRB6650S, Product Manual

Search results

Summary of Contents for DressPack IRB6650S

Reviews:

Brands by name

Popular brands