ABB DressPack IRB6650S Product Manual Download Page 268

Page: 268 / 390

Note

Action

xx1400000197

Refit the rear cover.

Screw M6x16 8.8-A2F (4 pcs)

Fitting the cable package

Note

Action

DANGER

Turn off all:

•

electric power supply

•

air pressure supply

to the robot, before starting the repair work on the
robot.

CAUTION

The cable package is sensitive to mechanical
damage. Handle it with care in order to avoid
damaging the cabling or the connectors.

xx1500001593

Fasten cable package with a velcro strap.

Push the cable package through the inside of the
lower arm.

Velcro straps (4 pcs)

Fasten the cable package to the robot cabling in-
side the lower arm with velcro straps.

Continues on next page

268

Product manual - DressPack/SpotPack IRB 6650S

3HAC055424-001 Revision: C

4 Repair

4.2.8 Replacing the cable package IRBDP MH LI

Continued

Summary of Contents for DressPack IRB6650S






































































































































































































































































































































































































Search results

Summary of Contents for DressPack IRB6650S

Reviews:

Brands by name

Popular brands

ABB DressPack IRB6650S, Product Manual

Search results

Summary of Contents for DressPack IRB6650S

Reviews:

Brands by name

Popular brands