ABB DressPack IRB6650S Product Manual Download Page 172

Page: 172 / 390

2.3 DressPack adjustments

2.3.1 Adjustments of - IRBDP MH2 UE and IRBDP SW2 UE

Note

This section is

not

applicable to cable package IRBDP MH3 UE! How to adjust

cable package IRBDP MH3 UE is detailed in

Adjustments of the cable package

- IRBDP MH3 UE on page 176

General

The instructions below details how to adjust the routing of the DressPack upper
arm to avoid reducing its life.

How to adjust the tension arm unit, see section

Adjusting tension arm unit on

page 320

Hose reinforcement

Should the hose reinforcement get strained under the upper arm during the work
cycle, the following tips may assist in alleviating the problem.

The figure shows a DressPack upper arm fitted to an IRB 6600, but the problem is
identical to all robot types.

xx0500001560

Note

Action

Either

try changing the robot position or orientation at
the particular position to reduce the angle of
axis 5 in combination of axis 6,

rotate the attachment angle of the process cable
support, axis 6 slightly.

Continues on next page

172

Product manual - DressPack/SpotPack IRB 6650S

3HAC055424-001 Revision: C

2 Installation

2.3.1 Adjustments of - IRBDP MH2 UE and IRBDP SW2 UE

Summary of Contents for DressPack IRB6650S






































































































































































































































































































































































































Search results

Summary of Contents for DressPack IRB6650S

Reviews:

Brands by name

Popular brands

ABB DressPack IRB6650S, Product Manual

Search results

Summary of Contents for DressPack IRB6650S

Reviews:

Brands by name

Popular brands