ABB DressPack IRB6650S Product Manual Download Page 353

Page: 353 / 390

Tightening torque (Nm)
Class 12.9, lubricated

Tightening torque (Nm)
Class 10.9, lubricated

Dimension

M10

120

M12

280

235

M16

550

460

M20

950

790

M24

Lubricated with Molycote 1000, Gleitmo 603 or equivalent

Water and air connectors

The following table specifies the recommended standard tightening torque for

water and air connectors

when

one

both

connectors are made of

brass

Note

A special torque specified in the repair, maintenance or installation procedure
overrides the standard torque.

Tightening torque Nm -
Max.

Tightening torque Nm -
Min.

Tightening torque Nm -
Nominal

Dimension

1/8

1/4

3/8

1/2

3/4

Product manual - DressPack/SpotPack IRB 6650S

353

3HAC055424-001 Revision: C

6 Reference information

6.3 Screw joints

Continued

Summary of Contents for DressPack IRB6650S






































































































































































































































































































































































































Search results

Summary of Contents for DressPack IRB6650S

Reviews:

Brands by name

Popular brands

ABB DressPack IRB6650S, Product Manual

Search results

Summary of Contents for DressPack IRB6650S

Reviews:

Brands by name

Popular brands