ABB DressPack IRB6650S Product Manual Download Page 148

Page: 148 / 390

Required tools and equipment

Note

Article number

Equipment

Content is defined in section

Standard toolkit on page 355

Standard toolkit

Required consumable

Note

Article number

Consumable

Loctite 243, for locking screws.

3HAB7116-1

Locking liquid

Cable grease

Fitting the cable package IRBDP MH LI

Connect the cable package at the base

Note

Action

DANGER

Turn off all:

•

electric power supply

•

hydraulic pressure supply

•

air pressure supply

to the robot, before entering the robot working
area.

CAUTION

The cable package is sensitive to mechanical
damage. Handle it with care in order to avoid
damaging the cabling or the connectors.

xx1500002963

Remove the rear cover plate.

xx1500002964

Remove the part of the backplate where the cus-
tomer plate is to be fitted. Hit the removable part
carefully with a plastic mallet.

Note

Only needed when the DressPack cable package
is fitted for the first time.

Continues on next page

148

Product manual - DressPack/SpotPack IRB 6650S

3HAC055424-001 Revision: C

2 Installation

2.2.10.2 Fitting the cable package IRBDP MH LI

Continued

Summary of Contents for DressPack IRB6650S






































































































































































































































































































































































































Search results

Summary of Contents for DressPack IRB6650S

Reviews:

Brands by name

Popular brands

ABB DressPack IRB6650S, Product Manual

Search results

Summary of Contents for DressPack IRB6650S

Reviews:

Brands by name

Popular brands