Zeiss Corona process Скачать руководство пользователя страница 9

Страница: 9 / 42

EN_40_070_0010I

Service manual | Lamp replacement and calibration - Corona process

Determining the device version

Lamp replacement and calibration Corona process

3 Determining the device version

Connecting the device to test computers and power supply

Connect the device to the measuring computer via the ethernet cable.

Establish the power supply for the device via the lab power supply.

Opening OSIS software

Start the

OSISManagementConsole.exe

under:

⇒

C:\Program Files (x86)\ZEISS\InProcess

⇒

C:\Program Files (x86)\ZEISS\InProcess\OSIS\ManagementConsole\

Selecting the device

Select the

Corona process

measuring system.

Fig. 3 Selecting the device

Enter the IP address of the measuring system or carry out a scan

Under

Hardware settings

IP address,

enter the IP address of your device or

carry out an address scan via the

Scan

button.

Ensure that you are working within the same IP address area when
connecting the device to the test computer.

Procedure

up to InProcess Version 2.9:

starting from InProcess

Version 2.10:

Содержание Corona process











































Результаты поиска

Содержание Corona process

Отзывы:

Похожие инструкции для Corona process

Бренды по названию

Популярные бренды

Zeiss Corona process, Руководство по обслуживанию

Результаты поиска

Содержание Corona process

Отзывы:

Похожие инструкции для Corona process

Бренды по названию

Популярные бренды