manualshive.com logo in svg

YASKAWA Sigma-V Series, Руководство пользователя

Поделиться
Скачать
YASKAWA Sigma-V Series Скачать руководство пользователя страница 186

5.9  Absolute Encoders

5-65

5

Ope

rat

ion

5.9

Absolute Encoders

If using an absolute encoder, a system to detect the absolute position can be designed for use with the host 

controller. As a result, an operation can be performed without a zero point return operation immediately after 

the power is turned ON.

A battery case is required to save position data in the absolute encoder.

The battery is attached to the battery case of the encoder cable.
If an encoder cable with a battery case is not used, install a battery to the host controller.

Set Pn002.2 to 0 (factory setting) to use the absolute encoder.

The SEN signal and battery are not required when using the absolute encoder as an incremental encoder.

 PROHIBITED

• Do not install batteries in both the host controller and battery case. It is dangerous because that sets up a 

loop circuit between the batteries.

Parameter

Meaning

When 

Enabled

Classification

Pn002

n. 0

 

[Factory setting] Uses the absolute encoder as an absolute encoder.

After restart

Setup

n. 1

Uses the absolute encoder as an incremental encoder.

The output range of the rotational serial data for the absolute position detecting system 
used for 

Σ

-

V

 large-capacity servo drives is different from that of SGDB 

Σ

 servo drives. As 

a result, the infinite-length positioning system of the 

Σ

 servo drives must be changed for 

use with 

Σ

-

V

 large-capacity servo drives. Be sure to make the following system modifica-

tions.

∗

The action differs when the multiturn limit setting (Pn205) is changed. Refer to 

5.9.6 Multiturn 

Limit Setting

.

SERVOPACK

Absolute 

Encoder 

Resolution

Output Range 

of Rotational 

Serial Data

Action when Limit Is Exceeded

Σ

 Series

   SGDB

12-bit
15-bit

-99999 to 
+ 99999

• When the upper limit (+99999) is exceeded 

in the forward direction, the rotational 
serial data will be 0.

• When the lower limit (-99999) is exceeded 

in the reverse direction, the rotational serial 
data will be 0.

Σ

-

II

, 

Σ

-

V (large-capacity)

  

Series

  SGDM

  SGDH

  SGDV

17-bit
20-bit

-32768 to 
+ 32767

• When the upper limit (+32767) is exceeded 

in the forward direction, the rotational 
serial data will be -32768.

*

• When the lower limit (-32768) is exceeded 

in the reverse direction, the rotational serial 
data will be +32767.

*

Содержание Sigma-V Series



















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды