Yamaha YZF-R1 2007 Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 442

background image

ENGINE

3-6

NOTE:

• The thickness “a” of each valve pad is

marked in hundredths of millimeters on the
side that touches the valve lifter.

• Since valve pads of various sizes are origi-

nally installed, the valve pad number must be
rounded in order to reach the closest equiva-
lent to the original.

c. Round off the original valve pad number

according to the following table.

EXAMPLE:
Original valve pad number = 148 (thickness
= 1.48 mm (0.058 in))
Rounded value = 150

d. Locate the rounded number of the original

valve pad and the measured valve clear-
ance in the valve pad selection table. The
point where the column and row intersect is
the new valve pad number.

NOTE:

The new valve pad number is only an approxi-
mation. The valve clearance must be mea-
sured again and the above steps should be
repeated if the measurement is still incorrect.

e. Install the new valve pad “1” and the valve

lifter “2”.

NOTE:

• Lubricate the valve pad with molybdenum

disulfide grease.

• Lubricate the valve lifter with molybdenum

disulfide oil.

• The valve lifter must turn smoothly when

rotated by hand.

• Install the valve lifter and the valve pad in the

correct place.

f.

Install the exhaust and intake camshafts,
timing chain and camshaft caps.

NOTE:

• Refer to "CAMSHAFTS" on page 5-9.
• Lubricate the camshaft bearings, camshaft

lobes and camshaft journals.

• First, install the exhaust camshaft.
• Align the camshaft marks with the camshaft

cap marks.

• Turn the crankshaft counterclockwise several

full turns to seat the parts.

g. Measure the valve clearance again.
h. If the valve clearance is still out of specifi-

cation, repeat all of the valve clearance
adjustment steps until the specified clear-
ance is obtained.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

7. Install:

• All removed parts

NOTE:

For installation, reverse the removal proce-
dure. Note the following points.

Last digit

Rounded value

0 or 2

0

5

5

8

10

Camshaft cap bolt

10 Nm (1.0 m·kg, 7.2 ft·lb)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
91
92
93
94
95
...
»

Содержание YZF-R1 2007



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZF-R1 2007

H-X-ADV-07-01-AL

Бренд: SRC Страницы: 6

690 Enduro R 2019

Бренд: KTM Страницы: 274

Бренд: Zontes Страницы: 119

Бренд: Miller Страницы: 12

Бренд: PUIG Страницы: 6

990D0-31J50-CLE

Бренд: Suzuki Страницы: 12

Бренд: Rivco Страницы: 5

Бренд: A.J.S. Страницы: 94

Бренд: yasuni Страницы: 8

Бренд: Yamaha Страницы: 120

Бренд: Gilera Страницы: 396

Бренд: Suzuki Страницы: 80

DRAG STAR XVS125

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 82

CRUX REV YD110-1 2016

Бренд: Yamaha Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды