Yamaha YZF-R1 2007 Скачать руководство пользователя страница 156

Страница: 156 / 442

FRONT BRAKE

4-27

NOTE:

Always install new brake pads and a new
brake pad spring as a set.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect a clear plastic hose “1” tightly to

the bleed screw “2”. Put the other end of
the hose into an open container.

b. Loosen the bleed screw and push the

brake caliper pistons into the brake caliper
with your finger.

c. Tighten the bleed screw.

d. Install new brake pads and a new brake

pad spring.

NOTE:

The arrow mark “a” on the brake pad springs
must point in the direction of disc rotation.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

6. Install:

• Brake pad pins
• Brake pad clips
• Brake caliper

7. Check:

• Brake fluid level

Below the minimum level mark “a”

→

Add

the recommended brake fluid to the proper
level.
Refer to "CHECKING THE BRAKE FLUID
LEVEL" on page 3-24.

8. Check:

• Brake lever operation

Soft or spongy feeling

→

Bleed the brake

system.
Refer to "BLEEDING THE HYDRAULIC
BRAKE SYSTEM" on page 3-26.

EAS22300

REMOVING THE FRONT BRAKE CALIPERS
The following procedure applies to both of the
brake calipers.

NOTE:

Before removing the brake caliper, drain the
brake fluid from the entire brake system.

1. Remove:

• Union bolt “1”
• Copper washers “2”
• Brake hose “3”

NOTE:

Put the end of the brake hose into a container
and pump out the brake fluid carefully.

Bleed screw

6 Nm (0.6 m·kg, 4.3 ft·lb)

Front brake caliper bolt

35 Nm (3.5 m·kg, 25 ft·lb)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Содержание YZF-R1 2007



























































































































































































































































































































































































































































Результаты поиска

Содержание YZF-R1 2007

Отзывы:

Похожие инструкции для YZF-R1 2007

Бренды по названию

Популярные бренды

Yamaha YZF-R1 2007, Руководство по обслуживанию

Результаты поиска

Содержание YZF-R1 2007

Отзывы:

Похожие инструкции для YZF-R1 2007

Бренды по названию

Популярные бренды