Yamaha YZF-R1 2007 Скачать руководство пользователя страница 288 | Manualshive

Страница: 288 / 442

background image

CRANKSHAFT

5-81

d. Put a piece of Plastigauge® “2” on each

crankshaft journal.

NOTE:

Do not put the Plastigauge® over the oil hole in
the crankshaft journal.

e. Install the crankshaft journal lower bear-

ings “1” into the lower crankcase and
assemble the crankcase halves.

NOTE:

• Align the projections “a” of the crankshaft

journal lower bearings with the notches “b” in
the lower crankcase.

• Do not move the crankshaft until the clear-

ance measurement has been completed.

f.

Tighten the bolts to specification in the
tightening sequence cast on the crankcase.

M9 x 105 mm (4.1 in) bolts: “1”–“10”
M8 x 60 mm (2.4 in) bolt: “11” LOCTITE®
M8 x 60 mm (2.4 in) bolts: “12”, “16”
M8 x 50 mm (2.0 in) bolts: “13”–“15”
M6 x 65 mm (2.5 in) bolts: “17”, “18”
M6 x 70 mm (2.8 in) bolts: “19”, “21”, “23”
M6 x 50 mm (2.0 in) bolts: “20”, “26”
M6 x 60 mm (2.4 in) bolt and washer: “22”
M6 x 60 mm (2.4 in) bolts: “24”, “25”
* Following the tightening order, loosen the
bolt one by one and then retighten it to the
specific torque.

NOTE:

Lubricate the crankcase bolt threads with
engine oil.
Refer to "CRANKCASE" on page 5-65.

g. Remove the lower crankcase and the

crankshaft journal lower bearings.

h. Measure the compressed Plastigauge®

width “c” on each crankshaft journal.
If the crankshaft-journal-to-crankshaft-jour-
nal bearing clearance is out of specifica-
tion, select replacement crankshaft journal
bearings.

Crankcase bolt

Bolt “1”–“10”
1st: 20 Nm (2.0 m·kg, 14 ft·lb)
2nd: 20 Nm (2.0 m·kg, 14 ft·lb)
3rd: +60

°

Bolt “11”–“16”
24 Nm (2.4m·kg, 17 ft·lb)
Bolt “17”–“26”
10 Nm (1.0m·kg, 7.2 ft·lb)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
286
287
288
289
290
...
»

Содержание YZF-R1 2007



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZF-R1 2007

750 Sport Bevel Heaven

Бренд: Ducati Страницы: 235

Бренд: LAZER Страницы: 19

Бренд: KYMCO Страницы: 69

Yamaha X-MAX 300

Бренд: BRUUDT Страницы: 7

Бренд: GAS GAS Страницы: 150

Бренд: CRATONI Страницы: 61

Бренд: GAS GAS Страницы: 107

TXT ROOKIE - 2006

Бренд: GAS GAS Страницы: 32

Operation and Instruction Manua

Бренд: Takegawa Страницы: 9

Бренд: Qingqi Страницы: 48

Бренд: Yadea Страницы: 100

Бренд: kellermann Страницы: 5

Бренд: DYNATEK Страницы: 6

Бренд: Magna Страницы: 223

Бренд: Peugeot Motorcycles Страницы: 50

Бренд: Klarfit Страницы: 8

Бренд: RIEJU Страницы: 72

Бренд: Roof Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды