Yamaha YZF-R1 2007 Скачать руководство пользователя страница 419

Страница: 419 / 442

ELECTRICAL COMPONENTS

8-92

battery charger cannot charge the MF battery.
A variable voltage charger is recommended.

d. Charge the battery until the battery’s charg-

ing voltage is 15 V.

NOTE:

Set the charging time at 20 hours (maximum).

e. Measure the battery open-circuit voltage

after leaving the battery unused for more
than 30 minutes.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

6. Install:

• Battery

7. Connect:

• Battery leads

(to the battery terminals)

CAUTION:

ECA13630

First, connect the positive battery lead “1”,
and then the negative battery lead “2”.

8. Check:

• Battery terminals

Dirt

→

Clean with a wire brush.

Loose connection

→

Connect properly.

9. Lubricate:

• Battery terminals

10. Install:

• Rider seat

Refer to "GENERAL CHASSIS" on page 4-
1.

EAS28040

CHECKING THE RELAYS
Check each switch for continuity with the
pocket tester. If the continuity reading is incor-
rect, replace the relay.

1. Disconnect the relay from the wire harness.
2. Connect the pocket tester (

Ω

1) and bat-

tery (12 V) to the relay terminal as shown.
Check the relay operation.

Out of specification

→

Replace.

Relay unit (starting circuit cut-off relay)

Relay unit (fuel pump relay)

12.8 V or more --- Charging is complete.
12.7 V or less --- Recharging is required.
Under 12.0 V --- Replace the battery.

Recommended lubricant

Dielectric grease

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

1. Positive battery terminal
2. Negative battery terminal
3. Positive tester probe
4. Negative tester probe

Relay operation

Continuity/No continuity

(between “3” to “4”)

1. Positive battery terminal
2. Negative battery terminal
3. Positive tester probe
4. Negative tester probe

Result

Continuity/No continuity

1. Positive battery terminal
2. Negative battery terminal
3. Positive tester probe
4. Negative tester probe

Result

Continuity/No continuity

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Содержание YZF-R1 2007



























































































































































































































































































































































































































































Результаты поиска

Содержание YZF-R1 2007

Отзывы:

Похожие инструкции для YZF-R1 2007

Бренды по названию

Популярные бренды

Yamaha YZF-R1 2007, Руководство по обслуживанию

Результаты поиска

Содержание YZF-R1 2007

Отзывы:

Похожие инструкции для YZF-R1 2007

Бренды по названию

Популярные бренды