Yamaha YZF-R1 2007 Скачать руководство пользователя страница 259 | Manualshive

Страница: 259 / 442

background image

CLUTCH

5-52

NOTE:

Assemble the friction plates and clutch plates
according to the installation order.

7. Install:

• Friction plate 1 “1”

NOTE:

Install the last friction plate shifting half phase
with the ø2 punch mark “2”.

8. Install:

• Bearing
• Pull rod
• Pressure plate 1 “1”

9. Install:

• Clutch springs
• Clutch spring bolts “1”

NOTE:

Tighten the clutch spring bolts in stages and in
a crisscross pattern.

10. Install:

• Push lever

NOTE:

Install the push lever with the “h” mark facing
toward upper side.

11. Install:

• Clutch cover
• Clutch cover gasket

NOTE:

• Install the push rod so that the teeth a face

towards the rear of the vehicle. Then, install
the clutch cover.

• Apply oil onto the bearing.
• Apply molybdenum disulfide grease onto the

push rod.

• When installing the clutch cover, push the

push lever and check that the punch mark “a”
on the push lever aligns with the mark “b” on
the clutch cover. Make sure that the push rod
teeth and push lever shaft pinion gear are
engaged.

Clutch spring bolt

10 Nm (1.0 m·kg, 7.2 ft·lb)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
257
258
259
260
261
...
»

Содержание YZF-R1 2007



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZF-R1 2007

Бренд: Racelogic Страницы: 2

Бренд: Suzuki Страницы: 447

CoreManual TorqDrive

Бренд: Rekluse Страницы: 20

990D0-31J50-CLE

Бренд: Suzuki Страницы: 12

Бренд: Denali Страницы: 5

Бренд: hepco & becker Страницы: 3

Бренд: yasuni Страницы: 8

Бренд: National Cycle Страницы: 2

Бренд: Triumph Страницы: 126

Бренд: Yamaha Страницы: 26

Бренд: Yamaha Страницы: 58

Бренд: Yamaha Страницы: 42

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 77

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 112

Бренд: Yamaha Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды