Yamaha YZF-R1 2007 Скачать руководство пользователя страница 364 | Manualshive

Страница: 364 / 442

background image

FUEL INJECTION SYSTEM

8-37

EAS27421

DIAGNOSTIC MODE
Setting the diagnostic mode
1. Turn the main switch to “OFF” and set the engine stop switch to “ON”.
2. Disconnect the wire harness coupler from the fuel pump.
3. Simultaneously press and hold the “SELECT” and “RESET” buttons, turn the main switch to

“ON”, and continue to press the buttons for 8 seconds or more.

NOTE:

• All displays on the meter disappear except the odometer/trip meter/fuel reservoir trip meter/stop

watch displays.

• “dIAG” appears on the odometer/trip meter/fuel reservoir trip meter/stop watch LCD.

4. Press the “SELECT” button to select the diagnostic mode “dIAG”.
5. After selecting “dIAG”, simultaneously press the “SELECT” and “RESET” buttons for 2 seconds

or more to activate the diagnostic mode. The diagnostic code number “d01” appears on the
odometer/trip meter/fuel reservoir trip meter/stop watch LCD.

6. Set the engine stop switch to “OFF”.
7. Select the diagnostic code number corresponding to the fault code number by pressing the

“SELECT” and “RESET” buttons.

NOTE:

The diagnostic code number appears on the odometer/trip meter/fuel reservoir trip meter/stop watch
LCD (01–70).
• To decrease the selected diagnostic code number, press the “RESET” button. Press the “RESET”

button for 1 second or longer to automatically decrease the diagnostic code numbers.

• To increase the selected diagnostic code number, press the “SELECT” button. Press the

“SELECT” button for 1 second or longer to automatically increase the diagnostic code numbers.

8. Verify the operation of the sensor or actuator.

• Sensor operation

The data representing the operating conditions of the sensor appears on the odometer/trip
meter/fuel reservoir trip meter/stop watch LCD.

• Actuator operation

Set the engine stop switch to “

” to operate the actuator.

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
362
363
364
365
366
...
»

Содержание YZF-R1 2007



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZF-R1 2007

Бренд: LAZER Страницы: 6

Бренд: Yamaha Страницы: 102

Бренд: Yamaha Страницы: 572

Бренд: Yamaha Страницы: 584

Бренд: Yamaha Страницы: 410

Бренд: Yamaha Страницы: 576

Бренд: Yamaha Страницы: 668

Бренд: Yamaha Страницы: 596

Бренд: Yamaha Страницы: 656

Бренд: Yamaha Страницы: 378

Бренд: N-Com Страницы: 2

Бренд: CF MOTO Страницы: 443

Бренд: rizoma Страницы: 10

Stelvio 1200 MY11 2011

Бренд: MOTO GUZZI Страницы: 385

Бренд: Big Dog Страницы: 100

SCARABEO 100 4T - 06-2001 PART6

Бренд: APRILIA Страницы: 6

Бренд: Miller Страницы: 22

Бренд: Kinroad Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды