Yamaha YZF-R1 2007 Скачать руководство пользователя страница 193 | Manualshive

Страница: 193 / 442

background image

REAR SHOCK ABSORBER ASSEMBLY

4-64

EAS23180

HANDLING THE REAR SHOCK ABSORBER

WARNING

EWA13740

This rear shock absorber contains highly
compressed nitrogen gas. Before handling
the rear shock absorber, read and make
sure you understand the following informa-
tion. The manufacturer cannot be held
responsible for property damage or per-
sonal injury that may result from improper
handling of the rear shock absorber.
• Do not tamper or attempt to open the rear

shock absorber.

• Do not subject the rear shock absorber to

an open flame or any other source of high
heat. High heat can cause an explosion
due to excessive gas pressure.

• Do not deform or damage the rear shock

absorber in any way. Rear shock absorber
damage will result in poor damping per-
formance.

EAS23190

DISPOSING OF A REAR SHOCK
ABSORBER
1. Gas pressure must be released before dis-

posing of a rear shock absorber. To release
the gas pressure, drill a 2–3-mm hole
through the rear shock absorber at a point
15–20 mm from its end as shown.

WARNING

EWA13760

Wear eye protection to prevent eye damage
from released gas or metal chips.

EAS23230

REMOVING THE REAR SHOCK ABSORBER
ASSEMBLY
1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there
is no danger of it falling over.

NOTE:

Place the vehicle on a suitable stand so that
the rear wheel is elevated.

2. Remove:

• Rear shock absorber assembly lower bolt

“1”

• Relay arm-to-swingarm bolt “2”

NOTE:

While removing the rear shock absorber
assembly lower bolt, hold the swingarm so that
it does not drop down.

3. Remove:

• Rear shock absorber upper bracket nut “1”
• Rear shock absorber assembly

NOTE:

Lower the swingarm, and the remove the rear
shock absorber assembly from between the
swingarm and frame.

EAS23240

CHECKING THE REAR SHOCK ABSORBER
ASSEMBLY
1. Check:

• Rear shock absorber rod

Bends/damage

→

Replace the rear shock

absorber assembly.

• Rear shock absorber

Gas leaks/oil leaks

→

Replace the rear

shock absorber assembly.

• Spring

Damage/wear

→

Replace the rear shock

absorber assembly.

• Bushings

Damage/wear

→

Replace.

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
191
192
193
194
195
...
»

Содержание YZF-R1 2007



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZF-R1 2007

Versaflo M Series

Бренд: 3M Страницы: 27

Speedglas 9100 Series

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 5

Бренд: Honda Страницы: 186

Бренд: GAS GAS Страницы: 32

2007 enducross EC

Бренд: GAS GAS Страницы: 72

Бренд: GAS GAS Страницы: 131

Бренд: hepco & becker Страницы: 4

Бренд: Can-Am Страницы: 60

Tarsafe TMA 10 G4

Бренд: Taramps Страницы: 16

Бренд: KTM Страницы: 240

Бренд: Denali Страницы: 2

Бренд: GMX Страницы: 20

Бренд: R&G Страницы: 3

Бренд: Noam Страницы: 14

Бренд: Baja motorsports Страницы: 22

DTS-i Discover 110 CBS

Бренд: Bajaj Auto Страницы: 40

Бренд: Yoshimura Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды