Yamaha YZF-R1 2007 Скачать руководство пользователя страница 185

Страница: 185 / 442

FRONT FORK

4-56

9. Fill:

• Front fork leg

(with the specified amount of the recom-
mended fork oil)

CAUTION:

ECA14230

• Be sure to use the recommended fork oil.

Other oils may have an adverse effect on
front fork performance.

• When disassembling and assembling the

front fork leg, do not allow any foreign
material to enter the front fork.

10. After filling the front fork leg, slowly stroke

the damper rod “1” up and down (at least
ten times) to distribute the fork oil.

NOTE:

Be sure to stroke the damper rod slowly
because the fork oil may spurt out.

11. Before measuring the fork oil level, wait ten

minutes until the oil has settled and the air
bubbles have dispersed.

NOTE:

Be sure to bleed the front fork leg of any resid-
ual air.

12. Measure:

• Front fork leg oil level “a”

Out of specification

→

Correct.

13. Install:

• Damper adjusting rod locknut “1”
• Fork spring “2”
• Spacer “3”
• Damper adjusting rod “4”
• Cap bolt “5”

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

Rod puller

90890-01437

Universal damping rod bleeding
tool set

YM-A8703

Rod puller attachment (M12)

90890-01435

Universal damping rod bleeding
tool set

YM-A8703

Quantity

513.0 cm³ (17.34 US oz) (18.09
Imp.oz)

Recommended oil

Suspension oil 01 or equiva-
lent

Level

101.0 mm (3.98 in)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Содержание YZF-R1 2007



























































































































































































































































































































































































































































Результаты поиска

Содержание YZF-R1 2007

Отзывы:

Похожие инструкции для YZF-R1 2007

Бренды по названию

Популярные бренды

Yamaha YZF-R1 2007, Руководство по обслуживанию

Результаты поиска

Содержание YZF-R1 2007

Отзывы:

Похожие инструкции для YZF-R1 2007

Бренды по названию

Популярные бренды