Yamaha YZF-R1 2007 Скачать руководство пользователя страница 177

Страница: 177 / 442

HANDLEBARS

4-48

4. Install:

• Throttle grip
• Throttle cable housing “1”
• Throttle cables

NOTE:

Align the projection “a” on the throttle cable
housing with the hole “b” in the right handlebar.

5. Install:

• Clutch lever holder “1”

NOTE:

Align the slit on the clutch lever holder with the
punch mark “a” on the left handlebar.

6. Install:

• Left handlebar switch “1”

NOTE:

Align the projection “a” on the left handlebar
switch with the hole “b” on the left handlebar.

7. Install:

• Handlebar grip

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Apply a thin coat of rubber adhesive onto

the end of the left handlebar.

b. Slide the handlebar grip over the end of the

left handlebar.

c. Wipe off any excess rubber adhesive with a

clean rag.

WARNING

EWA13700

Do not touch the handlebar grip until the
rubber adhesive has fully dried.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

8. Adjust:

• Clutch cable free play

Refer to "ADJUSTING THE CLUTCH
CABLE FREE PLAY" on page 3-14.

9. Adjust:

• Throttle cable free play

Refer to "ADJUSTING THE THROTTLE
CABLE FREE PLAY" on page 3-9.

EAS4C81004

CHECKING THE STEERING DAMPER
1. Check:

• Steering damper body

Damage/oil leaks

→

Replace.

(It replace with the assembly.)

• Steering damper rod

Bends/scratch

→

Replace.

(It replace with the assembly.)

Clutch lever free play

10.0–15.0 mm (0.39–0.59 in)

Throttle cable free play

3.0–5.0 mm (0.12–0.20 in)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Содержание YZF-R1 2007



























































































































































































































































































































































































































































Результаты поиска

Содержание YZF-R1 2007

Отзывы:

Похожие инструкции для YZF-R1 2007

Бренды по названию

Популярные бренды

Yamaha YZF-R1 2007, Руководство по обслуживанию

Результаты поиска

Содержание YZF-R1 2007

Отзывы:

Похожие инструкции для YZF-R1 2007

Бренды по названию

Популярные бренды