Yamaha YZF-R1 2007 Скачать руководство пользователя страница 417 | Manualshive

Страница: 417 / 442

background image

ELECTRICAL COMPONENTS

8-90

• Avoid bodily contact with electrolyte as it

can cause severe burns or permanent eye
injury.

FIRST AID IN CASE OF BODILY CONTACT:
EXTERNAL
• Skin — Wash with water.
• Eyes — Flush with water for 15 minutes

and get immediate medical attention.

INTERNAL
• Drink large quantities of water or milk fol-

lowed with milk of magnesia, beaten egg
or vegetable oil. Get immediate medical
attention.

CAUTION:

ECA13660

• This is a sealed battery. Never remove the

sealing caps because the balance
between cells will not be maintained and
battery performance will deteriorate.

• Charging time, charging amperage and

charging voltage for an MF battery are dif-
ferent from those of conventional batter-
ies. The MF battery should be charged as
explained in the charging method illustra-
tions. If the battery is overcharged, the
electrolyte level will drop considerably.
Therefore, take special care when charg-
ing the battery.

NOTE:

Since MF batteries are sealed, it is not possi-
ble to check the charge state of the battery by
measuring the specific gravity of the electro-
lyte. Therefore, the charge of the battery has to
be checked by measuring the voltage at the
battery terminals.

1. Remove:

• Rider seat

Refer to "GENERAL CHASSIS" on page 4-
1.

2. Disconnect:

• Battery leads

(from the battery terminals)

CAUTION:

ECA13640

First, disconnect the negative battery lead
“1”, and then positive battery lead “2”.

3. Remove:

• Battery

4. Check:

• Battery charge

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect a pocket tester to the battery ter-

minals.

NOTE:

• The charge state of an MF battery can be

checked by measuring its open-circuit volt-
age (i.e., the voltage when the positive bat-
tery terminal is disconnected).

• No charging is necessary when the open-cir-

cuit voltage equals or exceeds 12.8 V.

b. Check the charge of the battery, as shown

in the charts and the following example.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

5. Charge:

• Battery

(refer to the appropriate charging method
illustration)

WARNING

EWA13300

Do not quick charge a battery.

CAUTION:

ECA13670

• Never remove the MF battery sealing

caps.

• Do not use a high-rate battery charger

since it forces a high-amperage current

• Positive tester probe

→

positive battery terminal

• Negative tester probe

→

negative battery terminal

Example
Open-circuit voltage = 12.0 V
Charging time = 6.5 hours
Charge of the battery = 20–30%

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
415
416
417
418
419
...
»

Содержание YZF-R1 2007



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZF-R1 2007

Versaflo M Series

Бренд: 3M Страницы: 27

Speedglas 9100 Series

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 5

Бренд: Cobra Страницы: 2

Бренд: R&G Страницы: 4

Бренд: Gentex Страницы: 15

Бренд: Suzuki Страницы: 42

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 116

Tracer 9 GT 2021

Бренд: Yamaha Страницы: 126

Бренд: Yamaha Страницы: 116

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 116

Бренд: Yamaha Страницы: 87

Бренд: hepco & becker Страницы: 3

Бренд: DYNATEK Страницы: 4

Бренд: hepco & becker Страницы: 4

Бренд: SW-Motech Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды