Yamaha YZF-R1 2007 Скачать руководство пользователя страница 258

Страница: 258 / 442

CLUTCH

5-51

3. Install:

• Spring “1”

• Clutch boss nut “2”

NOTE:

• Put the spring detent “a” into the groove of

the pressure plate 2.
Assemble so that each spring detent “a” is
positioned in a different groove.

• While holding the clutch boss “3” with the

clutch holding tool “4”, tighten the clutch boss
nut.

• Lock the threads on the clutch boss nut by

staking them with a drift punch at the point
aligned with the groove in the axle.

4. Install:

• Clutch damper spring seat “1”
• Clutch damper spring “2”

NOTE:

Install the clutch damper spring as shown in
the illustration.

5. Lubricate:

• Friction plates
• Clutch plates

(with the recommended lubricant)

6. Install:

• Friction plate 3
• Friction plate 2
• Clutch plate 3
• Clutch plate 2
• Clutch plate 1 “1”

Clutch boss nut

115 Nm (11.5 m·kg, 83 ft·lb)

Universal clutch holder

90890-04086
YM-91042

New

Recommended lubricant

Engine oil

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Содержание YZF-R1 2007



























































































































































































































































































































































































































































Результаты поиска

Содержание YZF-R1 2007

Отзывы:

Похожие инструкции для YZF-R1 2007

Бренды по названию

Популярные бренды

Yamaha YZF-R1 2007, Руководство по обслуживанию

Результаты поиска

Содержание YZF-R1 2007

Отзывы:

Похожие инструкции для YZF-R1 2007

Бренды по названию

Популярные бренды