Yamaha YZF-R1 2007 Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 442

background image

CHASSIS

3-28

NOTE:

To maintain the proper wheel alignment, adjust
both sides evenly.

d. Tighten both locknuts to specification.

e. Tighten the wheel axle nut to specification.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS21440

LUBRICATING THE DRIVE CHAIN
The drive chain consists of many interacting
parts. If the drive chain is not maintained prop-
erly, it will wear out quickly. Therefore, the drive
chain should be serviced, especially when the
vehicle is used in dusty areas.
This vehicle has a drive chain with small rub-
ber O-rings between each side plate. Steam
cleaning, high-pressure washing, certain sol-
vents, and the use of a coarse brush can dam-
age these O-rings. Therefore, use only
kerosene to clean the drive chain. Wipe the
drive chain dry and thoroughly lubricate it with
engine oil or chain lubricant that is suitable for
O-ring chains. Do not use any other lubricants
on the drive chain since they may contain sol-
vents that could damage the O-rings.

EAS21500

CHECKING AND ADJUSTING THE STEER-
ING HEAD
1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there
is no danger of it falling over.

NOTE:

Place the vehicle on a suitable stand so that
the front wheel is elevated.

2. Check:

• Steering head

Grasp the bottom of the front fork legs and
gently rock the front fork.
Binding/looseness

→

Adjust the steering

head.

3. Remove:

• Upper bracket

Refer to "HANDLEBARS" on page 4-45
and "STEERING HEAD" on page 4-59.

4. Adjust:

• Steering head

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Remove the lock washer “1”, the upper ring

nut “2”, and the rubber washer “3”.

b. Loosen the lower ring nut “4” and then

tighten it to specification with a steering nut
wrench “5”.

NOTE:

Set the torque wrench at a right angle to the
steering nut wrench.

Direction “a”

Drive chain is tightened.

Direction “b”

Drive chain is loosened.

Locknut

16 Nm (1.6 m·kg, 12 ft·lb)

Wheel axle nut

150 Nm (15 m·kg, 108 ft·lb)

Recommended lubricant

Engine oil or chain lubricant
suitable for O-ring chains

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
113
114
115
116
117
...
»

Содержание YZF-R1 2007



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZF-R1 2007

Бренд: hepco & becker Страницы: 2

Бренд: Suzuki Страницы: 447

Бренд: paladin Страницы: 2

Бренд: RIEJU Страницы: 280

Бренд: Can-Am Страницы: 60

Бренд: Oxford Страницы: 2

Бренд: Vento Страницы: 88

Бренд: hepco & becker Страницы: 2

Бренд: KTM Страницы: 12

Бренд: Baja Страницы: 38

Бренд: Baja Страницы: 232

Бренд: Gazzini Страницы: 31

Бренд: Gazzini Страницы: 48

Victory Sport Cruiser 2001

Бренд: Polaris Страницы: 73

Бренд: R&G Страницы: 4

Бренд: Scorpa Страницы: 28

Speedglas 9100 MP

Бренд: 3M Страницы: 2

Caballero 125 series

Бренд: Fantic Страницы: 160

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды