Yamaha YZF-R1 2007 Скачать руководство пользователя страница 232

Страница: 232 / 442

VALVES AND VALVE SPRINGS

5-25

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

3. Eliminate:

• Carbon deposits

(from the valve face and valve seat)

4. Check:

• Valve face

Pitting/wear

→

Grind the valve face.

• Valve stem end

Mushroom shape or diameter larger than
the body of the valve stem

→

Replace the

valve.

5. Measure:

• Valve margin thickness “a”

Out of specification

→

Replace the valve.

6. Measure:

• Valve stem runout

Out of specification

→

Replace the valve.

NOTE:

• When installing a new valve, always replace

the valve guide.

• If the valve is removed or replaced, always

replace the oil seal.

EAS24300

CHECKING THE VALVE SEATS
The following procedure applies to all of the
valves and valve seats.
1. Eliminate:

• Carbon deposits

(from the valve face and valve seat)

2. Check:

• Valve seat

Pitting/wear

→

Replace the cylinder head.

3. Measure:

• Valve seat width “a”

Out of specification

→

Replace the cylinder

head.

Valve guide remover (ø4.5)

90890-04116

Valve guide remover (4.5 mm)

YM-04116

Valve guide remover (ø5)

90890-04097

Valve guide remover (5.0 mm)

YM-04097

Valve guide installer (ø4.5)

90890-04117

Valve guide installer (4.5 mm)

YM-04117

Valve guide installer (ø5)

90890-04098

Valve guide installer (5.0 mm)

YM-04098

Valve guide reamer (ø4.5)

90890-04118

Valve guide reamer (4.5 mm)

YM-04118

Valve guide reamer (ø5)

90890-04099

Valve guide reamer (5.0 mm)

YM-04099

Valve margin thickness

Valve margin thickness D
(intake)

1.10–1.50 mm (0.0433–0.0591
in)

Valve margin thickness D
(exhaust)

0.50–0.90 mm (0.0197–0.0354
in)

Valve stem runout

0.010 mm (0.0004 in)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Содержание YZF-R1 2007



























































































































































































































































































































































































































































Результаты поиска

Содержание YZF-R1 2007

Отзывы:

Похожие инструкции для YZF-R1 2007

Бренды по названию

Популярные бренды

Yamaha YZF-R1 2007, Руководство по обслуживанию

Результаты поиска

Содержание YZF-R1 2007

Отзывы:

Похожие инструкции для YZF-R1 2007

Бренды по названию

Популярные бренды