Yamaha YZF-R1 2007 Скачать руководство пользователя страница 373

Страница: 373 / 442

FUEL INJECTION SYSTEM

8-46

Fault code No.

Symptom

No normal signals are received from the cylinder identifi-
cation sensor when the engine is started or while the
vehicle is being driven.

Diagnostic code No.

—

Orde
r

Item/components and probable
cause

Check or maintenance job

Reinstatement
method

Installed condition of cylinder identifi-
cation sensor.

Check for looseness or pinching.

Cranking the
engine.

Connections
• Cylinder identification sensor cou-

pler

• Main wire harness ECU coupler

• Check the couplers for any pins

that may be pulled out.

• Check the locking condition of

the couplers.

• If there is a malfunction, repair it

and connect the coupler
securely.

Open or short circuit in wire harness.

• Repair or replace if there is an

open or short circuit.

• Between the cylinder identifica-

tion sensor coupler and ECU
coupler.
(Blue–Blue)
(White/Black–White/Black)
(Black/Blue–Black/Blue)

Defective cylinder identification sen-
sor.

• Replace if defective.

Refer to "CHECKING THE
CYLINDER IDENTIFICATION
SENSOR" on page 8-102.

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Содержание YZF-R1 2007



























































































































































































































































































































































































































































Результаты поиска

Содержание YZF-R1 2007

Отзывы:

Похожие инструкции для YZF-R1 2007

Бренды по названию

Популярные бренды

Yamaha YZF-R1 2007, Руководство по обслуживанию

Результаты поиска

Содержание YZF-R1 2007

Отзывы:

Похожие инструкции для YZF-R1 2007

Бренды по названию

Популярные бренды