Yamaha YZF-R1 2007 Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 442

background image

ENGINE

3-11

EAS20710

MEASURING THE COMPRESSION PRES-
SURE
The following procedure applies to all of the
cylinders.

NOTE:

Insufficient compression pressure will result in
a loss of performance.

1. Measure:

• Valve clearance

Out of specification

→

Adjust.

Refer to "ADJUSTING THE VALVE
CLEARANCE" on page 3-4.

2. Start the engine, warm it up for several

minutes, and then turn it off.

3. Disconnect:

• Ignition coils

4. Remove:

• Ignition coils
• Spark plugs

CAUTION:

ECA13340

Before removing the spark plugs, use com-
pressed air to blow away any dirt accumu-
lated in the spark plug wells to prevent it
from falling into the cylinders.

5. Install:

• Compression gauge “1”
• Extension

6. Measure:

• Compression pressure

Out of specification

→

Refer to steps (c)

and (d).

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Set the main switch to “ON”.
b. With the throttle wide open, crank the

engine until the reading on the compres-
sion gauge stabilizes.

WARNING

EWA4C81007

To prevent sparking, ground all speak plug
leads before cranking the engine.

NOTE:

The difference in compression pressure
between cylinders should not exceed 100 kPa
(1 kg/cm², 14 psi).

c. If the compression pressure is above the

maximum specification, check the cylinder
head, valve surfaces and piston crown for
carbon deposits.
Carbon deposits

→

Eliminate.

d. If the compression pressure is below the

minimum specification, pour a teaspoonful
of engine oil into the spark plug bore and
measure again.
Refer to the following table.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

7. Install:

• Spark plugs
• Ignition coils

Compression gauge

90890-03081

Engine compression tester

YU-33223

Extension

90890-04136

Standard compression pres-
sure (at sea level)

1480 kPa/350 r/min (210.5 psi/
350 r/min) (14.8 kgf/cm²/350 r/
min)

Minimum–Maximum

1290–1660 kPa (183.5–236.1
psi) (12.9–16.6 kgf/cm²)

Compression pressure (with oil applied into
the cylinder)
Reading

Diagnosis

Higher than without
oil

Piston ring(s) wear or
damage

→

Repair.

Same as without oil

Piston, valves, cylin-
der head gasket or
piston possibly defec-
tive

→

Repair.

Spark plug

13 Nm (1.3 m·kg, 9.4 ft·lb)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
96
97
98
99
100
...
»

Содержание YZF-R1 2007



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZF-R1 2007

Бренд: Yamaha Страницы: 32

Бренд: Yamaha Страницы: 860

Бренд: Dakota Digital Страницы: 11

Бренд: Honda Страницы: 93

Бренд: Yamaha Страницы: 287

Бренд: Yamaha Страницы: 109

Бренд: Suzuki Страницы: 101

Бренд: hepco & becker Страницы: 6

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 63

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 94

Star XV1900AE 2013

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 99

Бренд: Yamaha Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды