manualshive.com logo in svg

Yamaha YP125R, Руководство по обслуживанию

Скутер Yamaha YP125R - надежный и стильный транспорт для городских поездок. Чтобы правильно ухаживать за ним, важно иметь Owner's Manual. Скачайте бесплатно руководство по эксплуатации на manualshive.com и наслаждайтесь комфортом и удобством скутера Yamaha YP125R.

Поделиться
Скачать
background image

GENERAL CHASSIS

4-2

EAS37P1079

REMOVING THE STORAGE BOX

1. Remove:

• Storage box bolts “1”

TIP

Be sure not to let the storage box bolts fall inside 
the vehicle when removing them.

2. Remove:

• Storage box “1”

TIP

• Unhook the tabs “a” from the storage box.
• Remove the storage box by moving the seat 

hinge “2” in the direction of the arrow shown.

EAS37P1138

INSTALLING THE SEAT

1. Install:

• Safety protector

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Fold the tabs on the safety protector so that 

the holes in each tab are aligned, and then 
fasten the tabs to the storage box with the 
quick fastener screws at the locations “a” 
shown in the illustration.

b. Install the storage box, seat lock cable, water 

guard, and mudguard to the vehicle.

c. Pass the license plate light coupler (license 

plate light side) through the hole in the safety 
protector at the location “b” shown in the illus-
tration, and then connect the coupler.

d. Install the rear panels to the vehicle.
e. Align the holes in the safety protector with the 

projections on the water guard at the loca-
tions “c” shown in the illustration, and then 
fasten the safety protector with the clips at the 
locations where the holes are aligned with the 
projections.

TIP

Make sure that the edge of the safety protector 
is positioned to the inside of the rear panels at 
the location “d” shown in the illustration.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

2. Install:

• Mudguard

1

a

1

2

T

 

R

.

.

 

Mudguard bolt

11 Nm (1.1 m·kgf, 8.0 ft·lbf)
LOCTITE®

a

b

c

c

d

Содержание YP125R



















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YP125R

Yamaha LEXI Owner'S Manual preview
LEXI
Бренд: Yamaha Страницы: 112
Jetson Arro Manual preview
Arro
Бренд: Jetson Страницы: 56
Razor Bistro 15130640 Owner'S Manual preview
Bistro 15130640
Бренд: Razor Страницы: 14
Ebikes-Canada EBC-S18 User Manual preview
EBC-S18
Бренд: Ebikes-Canada Страницы: 34
Defiant DF-SK5H Manual preview
DF-SK5H
Бренд: Defiant Страницы: 42
Dominator The Commander User Manual preview
The Commander
Бренд: Dominator Страницы: 8
Hudora 14112 Instructions On Assembly And Use preview
14112
Бренд: Hudora Страницы: 8
Sterling Elite2 Plus Instructions For Use Manual preview
Elite2 Plus
Бренд: Sterling Страницы: 52
Dynacraft 24V eSKATEBOARD Owner'S Manual preview
24V eSKATEBOARD
Бренд: Dynacraft Страницы: 24
Trikke eV5 Owner'S Manual preview
eV5
Бренд: Trikke Страницы: 40
VESPA LX 4T USA Workshop Manual preview
LX 4T USA
Бренд: VESPA Страницы: 194
Riding'Times Q2 User Manual preview
Q2
Бренд: Riding'Times Страницы: 55
Razor W13111701003 Quick Manual preview
W13111701003
Бренд: Razor Страницы: 2
Razor Ultra Pro Owner'S Manual preview
Ultra Pro
Бренд: Razor Страницы: 5
Razor Rollie Owner'S Manual preview
Rollie
Бренд: Razor Страницы: 12
Active Mobility xtaga Impala User Manual preview
xtaga Impala
Бренд: Active Mobility Страницы: 26
Bluewheel HX380 Manual preview
HX380
Бренд: Bluewheel Страницы: 136
FREERIDER Luggie User Instruction Manual preview
Luggie
Бренд: FREERIDER Страницы: 33

Бренды по названию

Популярные бренды

Загрузить еще бренды